Antenna Mast Offset Mount Satellite Dish Support Bracket MM2 TV Minimount-2 DBS Off-Set Outdoor Support Add-On Tube Pipe Combo, Part # MM-2

Your price: $19.95

Antenna Mast Offset Mount Satellite Dish Support Bracket MM2 TV Minimount-2 DBS Off-Set Outdoor Support Add-On Tube Pipe Combo, Part # MM-2

This unit mounts into the bolt section of your existing satellite dish, and allows one to mount their off-air antenna very quickly and easily. An offset pipe (approx 24 inch) is also included (but not shown) that slides into the mount that makes installation fast, easy, professional, and pleasant to the eyes.

Retail Price: $29.95

Our Discounted Price: $19.95

Antenna Mast Chimney Mount 10' FT Straps TV Kit Brackets Support Philips Magnavox M61411 Complete Outdoor Off-Air Local Signal Mounting Hardware, Galvanized, Part # M-61411

Your price: $10.95

Antenna Mast Chimney Mount 10' FT Straps TV Kit Brackets Support Philips Magnavox M61411 Complete Outdoor Off-Air Local Signal Mounting Hardware, Galvanized, Part # M-61411

Allows you to mount an off-air roof top TV antenna to your chimney!!!

10' FT Chimney Mounting Straps!!!!

Tools needed: adjustable wrench or socket set.

Instructions:

1. Assemble straps with factory assembled eye-bolt bracket as shown.
2. Insert an eye-bolt into each bracket and thread nut onto about 1/2" from bolt to end.
3. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
4. Feed free end of strap through eye-bolt supplied.
5. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
6. Apply strap clamps.
7. Tighten eye-bolt nuts to secure strap around chimney.
8. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $16.95

Our Discounted Price: $10.95

Steren Z Chimney Mount Kit 10' FT Straps Antenna Mast Off-Air Signal Aerial Bracket Support with Stand-Off Mounting Straps and Hardware Install, 75 Ohm Connection, Part # CMK150

Your price: $10.95

Steren Z Chimney Mount Kit 10' FT Straps Antenna Mast Off-Air Signal Aerial Bracket Support with Stand-Off Mounting Straps and Hardware Install, 75 Ohm Connection, Part # CMK150

This TV Antenna Chimney Mounting Kit contains everything you will need for either a Twin lead or Coax Cable installation.

Contains:

• 1-Set of Chimney Mount Straps and Hardware
• 4-Screw-in Standoffs
• 2-Mast Clip-on Standoffs
• 4-Coaxial F Connectors
• 1-75 ohm Outdoor Matching Transformer
• 1-75 ohm Indoor Matching Transformer
• 1-75 ohm Indoor Push-on Matching Transformer
• 2-Cable Feed Thru Bushings
• 20-Coax Nail-in Fasteners

Antenna Wire Not Included.

Retail Price: $24.95

Our Discounted Price: $10.95

Winegard DS-1111 Easy Install Antenna Offset Mount Kit for Back of Satellite Dish Off-Air DS1111 Add-On Bracket Clamp, TV Mast Pipe, Part # DS1111

Your price: $10.89

Winegard DS-1111 Easy Install Antenna Offset Mount Kit for Back of Satellite Dish Off-Air DS1111 Add-On Bracket Clamp, TV Mast Pipe, Part # DS1111

ANTENNA MOUNT WINEGARD DS-1111 DBS satellite off air Antenna Mount is designed for use with most digital satellite home mounts. Clamp bracket included fits inside clamp bracket of satellite dish mount. Pipe is galvanized steel, 39 inches long, with a wall thickness of .060 inches, 1.66" OD and powder coated for maximum weather protection. Designed for use with outdoor off-air antennas.

Please Note: This mount is not designed for mounting on poles or vertical surfaces or for antennas with a boom length greater than 40".

Please Note: Satellite Dish / TV Antenna shown in picture are Not Included in this purchase.

Retail Price: $23.95

Our Discounted Price: $10.89

Winegard DS-2000 Universal 22" Pipe Tower Mount DS2000 Satellite Antenna Base Wall J Mount Pipe Dish TV Offset Support DS2000 Tower Roof Top Tube, Part # DS2000

Your price: $8.99

Winegard DS-2000 Universal 22" Pipe Tower Mount DS2000 Satellite Antenna Base Wall J Mount Pipe Dish TV Offset Support DS2000 Tower Roof Top Tube, Part # DS2000

Winegard’s DS-2000 Universal Pipe/Tower mount is a quick and economical mount for adding compact off-air antennas to your digital satellite system. Can be used on side of house or roof; mount foot can be used on either end of pipe for best mounting. With U-Bolts included, it is quickly adaptable to many different pole installation. Pipe galvanized steel, 22 inches long, with a wall thickness of .060 inches, 1.66" OD, E-Coated for maximum protection. If you need the extra length we have got it. Please Note: Not designed for large antennas.

Retail Price: $19.95

Our Discounted Price: $8.99

Winegard Mount DS-3000 J Pipe Antenna Dish 39" DS3000 DBS Satellite Outdoor TV Wall Support for Off-Air Free to Air, Rooftop Base Mast Tube, Part # DS-3000

Your price: $11.95

Winegard Mount DS-3000 J Pipe Antenna Dish 39" DS3000 DBS Satellite Outdoor TV Wall Support for Off-Air Free to Air, Rooftop Base Mast Tube, Part # DS-3000

Winegard’s DS-3000 J-Pipe mount is designed for outdoor antennas. Can be used on side of house or roof; mount foot can be used on either end of pipe for best mounting. Pipe galvanized steel, 39 inches long, with a wall thickness of .060 inches, 1.66" OD, E-Coated for maximum protection. Please Note: Mount is not designed for large directional antennas.

Retail Price: $29.95

Our Discounted Price: $11.95

Winegard DS-5002 Satellite Dish Chimney Mount DS5002 with 12' FT Steel Strap Complete DBS Support Bracket Hardware Kit Rooftop Outdoor Antenna Signal, Part # DS5002

Your price: $16.89

Winegard DS-5002 Satellite Dish Chimney Mount DS5002 with 12' FT Steel Strap Complete DBS Support Bracket Hardware Kit Rooftop Outdoor Antenna Signal, Part # DS5002

Easily mounts your DBS Satellite Dish Antenna to most chimneys. Made of durable steel with galvanized straps.

Includes:

• 1 Galvanized Steel Chimney Mount
• 2 Galvanized Steel Straps 12'
• 4 Hex Bolts 1/2"
• 8 Flat Washers 1/4"
• 4 Hex Nuts 1/4"
• 4 Lock Washers
• 4 Tri-Bolts
• 4 Screw Type Strap Grips

Retail Price: $39.95

Our Discounted Price: $16.89

Winegard DS-5146 Roof Mount Pipe Support for Non-Penetrating Frame Satellite Dish Antenna 1.66" Pole and Angle Supports, Part # DS-5146

Your price: $7.95

Winegard DS-5146 Roof Mount Pipe Support for Non-Penetrating Frame Satellite Dish Antenna 1.66" Pole and Angle Supports, Part # DS-5146

Winegard's Non-Penetrating Roof Mounts solve the problems associated with flat-roof installations. They are also an alternative when a non-permanent installation is required, or one that may be moved to other sites. Base frames and post kits can be combined in various ways to support antennas up to one meter. The post is steel with sturdy aluminum braces. Base frame and post have a seven step thermoset powder coat finish.

This purchase is for the Winegard Model DS-5146 Post Kit. This post will support antennas up to 76 cm when used with the single base frame. Includes pole and braces. Pole size 1.66" OD, 19" long, 16 ga steel.

Retail Price: $19.95

Our Discounted Price: $7.95

Winegard DS-5046 Non-Penetrating Roof Mount DS5046 Satellite Dish Antenna Base, Flat Steel Square Frame Support, Part # DS5046

Your price: $26.89

Winegard DS-5046 Non-Penetrating Roof Mount DS5046 Satellite Dish Antenna Base, Flat Steel Square Frame Support, Part # DS5046

Winegard's Non-Penetrating Roof Mounts solve the problems associated with flat-roof installations. They are also an alternative when a non-permanent installation is required, or one that may be moved to other sites. Base frames and post kits can be combined in various ways to support antennas up to one meter. The base frame is manufactured from 1.25" x 1.25" x 0.188" angle iron. Base frame has a seven step thermoset powder coat finish. This base is PRE-DRILLED to fit most antenna bases.

The Winegard Model Single Base Frame, for 46 and 60 cm antennas with Winegard, RCA, Sony, ITI and other mounting feet. Single base frame covers approximately six square feet. 25.5" x 37.5" square.

Please Note: Pole Mount and Rubber Mat not included. This listing is for the purchase of the Base Section Only.

Retail Price: $69.95

Our Discounted Price: $26.89

Magnetic Compass Directional North South Round 1 1/2" Direction Finder 1.5" Inch Silver Metal Case, Install Off-Air Satellite Dish HDTV Antenna Positioning Tool, Polarity Device

Your price: $1.25

Magnetic Compass Directional North South Round 1 1/2" Direction Finder 1.5" Inch Silver Metal Case, Install Off-Air Satellite Dish HDTV Antenna Positioning Tool, Polarity Device

• 1 1/2" Compass, a must have for DBS installation kit
• Used in initial dish positioning
• A must have to install your dish properly.

Retail Price: $2.95

Our Discounted Price: $1.25

Magnetic Compass Direction Polarity 1 1/4" Round Sky Satellite Dish HDTV Antenna North South Positioning, The Angle Position Finder

Your price: $0.95

Magnetic Compass Direction Polarity 1 1/4" Round Sky Satellite Dish HDTV Antenna North South Positioning, The Angle Position Finder

• 1 1/4" Compass, a must have for DBS installation kit
• Used in initial dish positioning
• A must to install your dish properly.

Retail Price: $1.95

Our Discounted Price: $0.95

DIRECTV Satellite Dish Self Installation Kit TV Antenna Install Coax Cable Kit Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Your price: $12.95

DIRECTV Satellite Dish Self Installation Kit TV Antenna Install Coax Cable Kit Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Alphastar digital satellite television do-it-yourself installation kit. Everything you need to do a professional installation of your DBS satellite system or to move it to another location.

Includes:

• installation manual and installation video
• 75 ft coax cable with weatherproof boot
• 25 ft RG-6 coax cable
• silicone sealant 3 oz.
• 30 ft grounding wire
• grounding block
• grounding strap
• compass
• 4 cable ties
• 4 wall anchors
• 4 lag screws 2" x 1/4"
• 2 lag screws 3" x 1/4"
• 4 flat washers
• 4 machined screws 1/4" x 2/3"
• Simple tools required

Retail Price: $39.95

Our Discounted Price: $12.95

Bubble Level Magnetic Base Horizontal Vertical Axis for DBS DSS Satellite Dish Alignment TV Signal Antenna Base Pipe, North South Tool

Your price: $1.89

Bubble Level Magnetic Base Horizontal Vertical Axis for DBS DSS Satellite Dish Alignment TV Signal Antenna Base Pipe, North South Tool

Specifications:

• Magnetic Base
• Easy to use.
• A must to install your dish mount properly.

Retail Price: $3.95

Our Discounted Price: $1.89

Antenna Mast Offset Mount Mini MM3 Satellite Minimount-3 DBS Dish Off-Set Off-Air Outdoor Signal Taller Add-On Combo, 40" Long Bracket Support, Part # MM-3

Your price: $19.95

Antenna Mast Offset Mount Mini MM3 Satellite Minimount-3 DBS Dish Off-Set Off-Air Outdoor Signal Taller Add-On Combo, 40" Long Bracket Support, Part # MM-3

This product is no longer available for purchase.

Please check out our Antenna Mount Section for similar products!!!!

This unit mounts into the bolt section of your existing satellite dish, and allows one to mount their off-air antenna very quickly and easily. An offset pipe (40" LONG and 1 5/16" WIDE) is included that slides into the mount that makes installation fast, easy, professional, and pleasant to the eyes. Please Note: Antenna NOT included.

Retail Price: $39.95

Our Discounted Price: $19.95

Satellite Dish Antenna Fastener Bolt Pack Panel Reflector Replacement Hardware

Your price: $1.95

Satellite Dish Antenna Fastener Bolt Pack Panel Reflector Replacement Hardware

DSS Satellite Dish Nuts and Bolt Pack

• Nuts and Bolt hardware to allow for easy set-up between mount and dish
• package will work for 18", 24" and 1 meter dishes

Retail Price: $3.95

Our Discounted Price: $1.95

Satellite Polorotor C-Band Feed Gasket LNA LNB Feedhorn Elbow Chaparral Satellite Dish Waterproof Seal Gaskets

Your price: $0.49

Satellite Polorotor C-Band Feed Gasket LNA LNB Feedhorn Elbow Chaparral Satellite Dish Waterproof Seal Gaskets

Chaparral Water Proof LNA / LNB C-Band Satellite Feedhorn Elbow Gaskets

• Commercial Grade
• Rubber Seal
• Single Units

Retail Price: $0.99

Our Discounted Price: $0.49

Lensatic Compass Liquid Filled Magnetic Directional Engineers for North South Map Positioning with Rugged Metal Case and Easy Readability, Polarity Direction Finder, Part # DC453B

Your price: $4.95

Lensatic Compass Liquid Filled Magnetic Directional Engineers for North South Map Positioning with Rugged Metal Case and Easy Readability, Polarity Direction Finder, Part # DC453B

• Liquid Filled for Fast Reads
• Sturdy Metal Case
• Floating Luminous Dial - Easy to Read
• Adjustable Luminous Marching Line
• Thumb Hold Magnifying Viewer
• Sighting Hairline
• Ideal for locating position on a map or in the field

Retail Price: $9.95

Our Discounted Price: $4.95

Satellite Dish Non-Penetrating Roof Mount DirecWay Flat Square Base Heavy Duty NPR7KD Off-Air Antenna Signal Roof Mount, Steel Frame and Pipe Support, Angle Brackets for Sat Reflectors, Part # NPR-7KD

Your price: $169.95

Satellite Dish Non-Penetrating Roof Mount DirecWay Flat Square Base Heavy Duty NPR7KD Off-Air Antenna Signal Roof Mount, Steel Frame and Pipe Support, Angle Brackets for Sat Reflectors, Part # NPR-7KD

This antenna roof mount is no longer available for purchase.

Similar products can be found in the Satellite Antenna Mount Section!!!

Perfect Vision Non-Penetrating Roof Mounts solve the problems associated with flat-roof installations. They are also an alternative when a non-permanent installation is required, or one that may be moved to other sites. This base frame and post kit creates various ways to easily support antennas up to one meter, and elliptical dish applications (i.e. satellite broadband Internet). The base frame is manufactured from heavy gauge angle iron, and accommodates either a 2 7/8" or 2 3/8 mast pipe. We have also included the roof base pad for this 18 block capacity mount. Blocks Not Included.

Retail Price: $229.95

Our Discounted Price: $169.95

Channel Master 3009 TV Antenna Mount CM3009 Satellite Dish Wall Roof J Pipe 22" Universal Outdoor Off-Air Aerial Support, Part # CM-3009

Your price: $15.95

Channel Master CM3009 Universal J Pipe TV Antenna mount is a quick and economical mount for adding compact off-air antennas to your digital satellite system. It can be used on side of house or roof; mount foot can be used on either end of pipe for best mounting. With U-Bolts included, it is quickly adaptable to many different pole installation. Pipe galvanized steel, 22 inches long, with a wall thickness of .060 inches, 1.66" OD, E-Coated for maximum protection. Please Note: This mount is not designed for large antennas.

Retail Price: $39.79

Our Discounted Price: $15.95

Satellite Do It Yourself Installation Kit DIRECTV Satellite DBS Dish Self Install Kit TV Antenna Coax Cable Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Your price: $12.95

Satellite Do It Yourself Installation Kit DIRECTV Satellite DBS Dish Self Install Kit TV Antenna Coax Cable Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Alphastar digital satellite television do-it-yourself installation kit. Everything you need to do a professional installation of your DBS satellite system or to move it to another location.

Includes:

• installation manual and installation video
• 75 ft coax cable with weatherproof boot
• 25 ft RG-6 coax cable
• silicone sealant 3 oz.
• 30 ft grounding wire
• grounding block
• grounding strap
• compass
• 4 cable ties
• 4 wall anchors
• 4 lag screws 2" x 1/4"
• 2 lag screws 3" x 1/4"
• 4 flat washers
• 4 machined screws 1/4" x 2/3"
• Simple tools required

Retail Price: $39.95

Our Discounted Price: $12.95

DBS Satellite Dish Installation Kit DIRECTV Satellite Dish Self Install Kit TV Antenna Coax Cable Kit Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Your price: $12.95

DBS Satellite Dish Installation Kit DIRECTV Satellite Dish Self Install Kit TV Antenna Coax Cable Kit Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Alphastar digital satellite television do-it-yourself installation kit. Everything you need to do a professional installation of your DBS satellite system or to move it to another location.

Includes:

• installation manual and installation video
• 75 ft coax cable with weatherproof boot
• 25 ft RG-6 coax cable
• silicone sealant 3 oz.
• 30 ft grounding wire
• grounding block
• grounding strap
• compass
• 4 cable ties
• 4 wall anchors
• 4 lag screws 2" x 1/4"
• 2 lag screws 3" x 1/4"
• 4 flat washers
• 4 machined screws 1/4" x 2/3"
• Simple tools required

Retail Price: $39.95

Our Discounted Price: $12.95

Satellite TV Installation Kit DIRECTV DBS Dish Self Install Kit TV Antenna Coax Cable Kit Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Your price: $12.95

Satellite TV Installation Kit DIRECTV DBS Dish Self Install Kit TV Antenna Coax Cable Kit Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Alphastar digital satellite television do-it-yourself installation kit. Everything you need to do a professional installation of your DBS satellite system or to move it to another location.

Includes:

• installation manual and installation video
• 75 ft coax cable with weatherproof boot
• 25 ft RG-6 coax cable
• silicone sealant 3 oz.
• 30 ft grounding wire
• grounding block
• grounding strap
• compass
• 4 cable ties
• 4 wall anchors
• 4 lag screws 2" x 1/4"
• 2 lag screws 3" x 1/4"
• 4 flat washers
• 4 machined screws 1/4" x 2/3"
• Simple tools required

Retail Price: $39.95

Our Discounted Price: $12.95

Satellite RG6 Coaxial Cable Kit DIRECTV Installation DBS Dish Self Install Kit TV Antenna Coax Cable Kit Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Your price: $12.95

Satellite RG6 Coaxial Cable Kit DIRECTV Installation DBS Dish Self Install Kit TV Antenna Coax Cable Kit Alphastar Hardware Professional Install Sky Kit Deluxe, Do It Yourself

Alphastar digital satellite television do-it-yourself installation kit. Everything you need to do a professional installation of your DBS satellite system or to move it to another location.

Includes:

• installation manual and installation video
• 75 ft coax cable with weatherproof boot
• 25 ft RG-6 coax cable
• silicone sealant 3 oz.
• 30 ft grounding wire
• grounding block
• grounding strap
• compass
• 4 cable ties
• 4 wall anchors
• 4 lag screws 2" x 1/4"
• 2 lag screws 3" x 1/4"
• 4 flat washers
• 4 machined screws 1/4" x 2/3"
• Simple tools required

Retail Price: $39.95

Our Discounted Price: $12.95

Winegard DS-2016 Antenna Mount Satellite Wall Base 28" J Pipe DS2016 Dish TV Universal Offset Support DS2000 Tower Roof Top Tube, Part # DS2016

Your price: $12.89

Winegard DS-2016 Antenna Mount Satellite Wall Base 28" J Pipe DS2016 Dish TV Universal Offset Support DS2000 Tower Roof Top Tube, Part # DS2016

Winegard - Clearly the Worlds Best!!!

Winegard’s DS-2016 Universal Pipe/Tower mount is a quick and economical mount for adding compact off-air antennas to your digital satellite system. Can be used on side of house or roof; mount foot can be used on either end of pipe for best mounting. With U-Bolts included, it is quickly adaptable to many different pole installation. Pipe galvanized steel, 28 inches long, with a wall thickness of .060 inches, 1.66" OD, E-Coated for maximum protection. If you need the extra length we have got it. (Please Note: Not designed for large antennas.)

Retail Price: $29.95

Our Discounted Price: $12.89

Channel Master 9067 Chimney Mount Y Type Antenna Mast 18' FT Chimney Straps CM9067 Install Kit, Complete Outdoor Off-Air Antenna Aerial Chimney Mounting Hardware, Stainless Steel Straps, Part # CM-9067

Your price: $13.95

Channel Master 9067 Chimney Mount Y Type Antenna Mast 18' FT Chimney Straps CM9067 Install Kit, Complete Outdoor Off-Air Antenna Aerial Chimney Mounting Hardware, Stainless Steel Straps, Part # CM-9067

Allows you to mount an off-air roof top TV antenna to your chimney!!!

18' FT Chimney Mounting Straps!!!!

Specifications:

• (2) "Y" Chimney Straps
• (2) 18' FT Stainless Steel Chimney Straps

Instructions:

1. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
2. Feed free end of strap through.
3. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
4. Apply strap clamps.
5. Tighten to secure straps around chimney.
6. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $24.95

Our Discounted Price: $13.95

Channel Master 3092 3' FT Tripod Mount Heavy Duty Tri-Pod Antenna Mast Support CM3092 Outdoor Off-Air TV Aerial Stand-Off Kit with Pitch Pads and Lag Bolts, Part # CM-3092

Your price: $24.95

Channel Master 3092 3' FT Tripod Mount Heavy Duty Tri-Pod Antenna Mast Support CM3092 Outdoor Off-Air TV Aerial Stand-Off Kit with Pitch Pads and Lag Bolts, Part # CM-3092

Lag Bolts and Pitch Pads Included Free for Easy Installation!!!

Channel Master 3092 tripod antenna mount is designed to handle up to 1 3/4" diameter masts. Lag bolts and pitch pads are furnished to secure the mount to your roof.

Specifications:

• Heavy Duty 3' FT Tripod Antenna Mount
• Fits up to 1 3/4" Mast Pipes
• Lag Bolts Included
• Pitch Pads Included
• Galvanized Steel

Retail Price: $46.95

Our Discounted Price: $24.95

Channel Master 9004 5' FT Tripod Mount Heavy Duty Antenna Tri-Pod Mast Support CM9004 Outdoor Off-Air TV Aerial Stand-Off Kit, Part # CM-9004

Your price: $34.95

Channel Master 9004 5' FT Tripod Mount Heavy Duty Antenna Tri-Pod Mast Support CM9004 Outdoor Off-Air TV Aerial Stand-Off Kit, Part # CM-9004

Channel Master - A name you can trust!!!

Channel Master 9004 5' FT tripod antenna mount is designed to handle up to 1 3/4" diameter masts. Perfect for camping, and sports tailgating applications.

Specifications:

• Heavy Duty 5' FT Tripod Antenna Mount
• Fits up to 1 3/4" Mast Pipes
• Galvanized Steel

Retail Price: $59.95

Our Discounted Price: $34.95

Channel Master 9138 3' FT Tripod Mount Antenna Tri-Pod Mast Support CM9138 Outdoor Off-Air TV Aerial Stand-Off Kit, Part # CM-9138

Your price: $24.95

Channel Master 9138 3' FT Tripod Mount Antenna Tri-Pod Mast Support CM9138 Outdoor Off-Air TV Aerial Stand-Off Kit, Part # CM-9138

This item is no longer available for purchase.

It has been replaced by the Perfect Vision Heavy Duty Tri-Pod!!!!

Channel Master - A Name You can Trust!!!

Channel Master 9138 3' FT tripod antenna mount is designed to handle up to 1 3/4" diameter masts. Perfect for camping, and sports tailgating applications.

Specifications:

• 3' FT Tripod Antenna Base Mount
• Fits up to 1 3/4" Mast Pipes
• Galvanized Steel

Retail Price: $39.95

Our Discounted Price: $24.95

DIRECTV AU9S Slimline Monopole Satellite Dish Antenna Pipe Mount Arm AU9-S Bracket Support Strut Arm Long Brace Satellite Dish, Arm Pipe Support Fits 2" Dish Masts, AT9, Part # DTVA3-Longbrace

Your price: $3.89

DIRECTV AU9S Slimline Monopole Satellite Dish Antenna Pipe Mount Arm AU9-S Bracket Support Strut Arm Long Brace Satellite Dish, Arm Pipe Support Fits 2" Dish Masts, AT9, Part # DTVA3-Longbrace

The DIRECTV Slimline Multi-Satellite Dish antenna arm support bracket add-on. Mast support extends from 19" to 32" in length and accommodates both standard 2" mast supports.

Specifications:

• Extends from 19" - 32" Mast Pipe Support Arm Bracket
• Fits 2" Mast Pipes
• Easy to Install
• Bulk Packaged

Retail Price: $9.95

Our Discounted Price: $3.89

Antenna 10' FT Chimney Strap Mast Mount Kit Gemini Off-Air Signal Aerial Bracket Support with Stand-Off Mounting Contains 10 Foot Straps and Hardware Install, 75 Ohm Connection, Part # CMK150

Your price: $10.95

Antenna 10' FT Chimney Strap Mast Mount Kit Gemini Off-Air Signal Aerial Bracket Support with Stand-Off Mounting Contains 10 Foot Straps and Hardware Install, 75 Ohm Connection, Part # CMK150

This TV Antenna Chimney Mounting Kit contains everything you will need for either a Twin lead or Coax Cable installation.

Contains:

• 1-Set of Chimney Mount Straps and Hardware
• 4-Screw-in Standoffs
• 2-Mast Clip-on Standoffs
• 4-Coaxial F Connectors
• 1-75 ohm Outdoor Matching Transformer
• 1-75 ohm Indoor Matching Transformer
• 1-75 ohm Indoor Push-on Matching Transformer
• 2-Cable Feed Thru Bushings
• 20-Coax Nail-in Fasteners

Antenna Wire Not Included.

Retail Price: $24.95

Our Discounted Price: $10.95

Steren 10' FT Z Type Chimney Mount Kit Contains 10' FT Galvanized Strap Brackets TV Aerial Support Complete Outdoor Off-Air Local Signal Mounting Hardware

Your price: $9.95

Steren 10' FT Z Type Chimney Mount Kit Contains 10' FT Galvanized Strap Brackets TV Aerial Support Complete Outdoor Off-Air Local Signal Mounting Hardware

Allows you to mount an off-air roof top TV antenna to your chimney!!!

10' FT Chimney Mounting Straps!!!!

Tools needed: adjustable wrench or socket set.

Instructions:

1. Assemble straps with factory assembled eye-bolt bracket as shown.
2. Insert an eye-bolt into each bracket and thread nut onto about 1/2" from bolt to end.
3. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
4. Feed free end of strap through eye-bolt supplied.
5. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
6. Apply strap clamps.
7. Tighten eye-bolt nuts to secure strap around chimney.
8. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $16.95

Our Discounted Price: $9.95

Satellite Dish Chimney Mount Winegard DS-5002 DS5002 with 12' FT Steel Strap Complete DBS Support Bracket Hardware Kit Rooftop Outdoor Antenna Signal, Part # DS5002

Your price: $16.89

Satellite Dish Chimney Mount Winegard DS-5002 DS5002 with 12' FT Steel Strap Complete DBS Support Bracket Hardware Kit Rooftop Outdoor Antenna Signal, Part # DS5002

Easily mounts your DBS Satellite Dish Antenna to most chimneys. Made of durable steel with galvanized straps.

Includes:

• 1 Galvanized Steel Chimney Mount
• 2 Galvanized Steel Straps 12'
• 4 Hex Bolts 1/2"
• 8 Flat Washers 1/4"
• 4 Hex Nuts 1/4"
• 4 Lock Washers
• 4 Tri-Bolts
• 4 Screw Type Strap Grips

Retail Price: $39.95

Our Discounted Price: $16.89

Mini-Mount Antenna Mast Bracket Add-On Support Fits Standard Satellite Mast Pipe Outdoor Off-Air TV Aerial Stand-Off Bracket Support, Part # MMBRACKET

Your price: $6.95

Antenna Mast Bracket Mini-Mount Add-On Mounting Support Fits Standard Satellite Mast Pipe Outdoor Off-Air TV Aerial Stand-Off Bracket Support, Part # MMBRACKET

This antenna mount bracket allows you to install an off-air HD TV antenna above your existing satellite dish. Simply attach this bracket to the azimuth adjustment bolts on your standard satellite dish, slide your new antenna mast pipe into the bracket and tighten it down. It is constructed out of heavy-duty galvanized steel that will withstand the elements. The simple, yet efficient design is Easy to install!!!

Specifications:

• Antenna Mast Satellite Dish Add-On Mini-Mount Bracket Universal Support
• Fits 1 1/4" Standard Satellite Dish Antenna Mast Pipe

Retail Price: $14.95

Our Discounted Price: $6.95

Winegard DS1111 Antenna Mount for Satellite Dishes HDTV Products Easy Install Offset Kit Off-Air Add-On Bracket Clamp, TV Mast Pipe, Part # DS-1111

Your price: $10.89

Winegard DS1111 Antenna Mount for Satellite Dishes HDTV Products Easy Install Offset Kit Off-Air Add-On Bracket Clamp, TV Mast Pipe, Part # DS-1111

ANTENNA MOUNT WINEGARD DS1111 DBS satellite off air Antenna Mount is designed for use with most digital satellite home mounts. Clamp bracket included fits inside clamp bracket of satellite dish mount. Pipe is galvanized steel, 39 inches long, with a wall thickness of .060 inches, 1.66" OD and powder coated for maximum weather protection. Designed for use with outdoor off-air antennas.

Please Note: This mount is not designed for mounting on poles or vertical surfaces or for antennas with a boom length greater than 40".

Please Note: Satellite Dish / TV Antenna shown in picture are Not Included in this purchase.

Retail Price: $23.95

Our Discounted Price: $10.89

Channel Master 3080 Antenna Chimney Mount 12' FT Z Type Antenna Mast Chimney Straps CM3080 Install Kit, Complete Outdoor Off-Air Antenna Aerial Chimney Mounting Hardware, Stainless Steel Straps, Part # CM-3080

Your price: $9.95

Channel Master 3080 Antenna Chimney Mount 12' FT Z Type Antenna Mast Chimney Straps CM3080 Install Kit, Complete Outdoor Off-Air Antenna Aerial Chimney Mounting Hardware, Stainless Steel Straps, Part # CM-3080

Allows you to mount an off-air roof top TV antenna to your chimney!!!

12' FT Chimney Mounting Straps!!!!

Specifications:

• (2) "Z" Type Chimney Straps
• (2) 12' FT Stainless Steel Chimney Straps

Instructions:

1. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
2. Feed free end of strap through.
3. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
4. Apply strap clamps.
5. Tighten to secure straps around chimney.
6. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $19.95

Our Discounted Price: $9.95

Satellite Dish Offset Mast Mount Antenna Mast Mini MM3 Mount Satellite Minimount-3 DBS Dish Off-Set Outdoor Signal Taller Add-On Combo, 40" Long Bracket Support, Part # MM-3

Your price: $19.95

Satellite Dish Offset Mast Mount Antenna Mast Mini MM3 Mount Satellite Minimount-3 DBS Dish Off-Set Outdoor Signal Taller Add-On Combo, 40" Long Bracket Support, Part # MM-3

This product is no longer available for purchase.

Please check out our Antenna Mount Section for similar products!!!!

This unit mounts into the bolt section of your existing satellite dish, and allows one to mount their off-air antenna very quickly and easily. An offset pipe (40" LONG and 1 5/16" WIDE) is included that slides into the mount that makes installation fast, easy, professional, and pleasant to the eyes. Please Note: Antenna NOT included.

Retail Price: $39.95

Our Discounted Price: $19.95

DIRECTV Brace Support Slimline AU9S Monopole Satellite Dish Antenna Pipe Mount Arm AU9-S Bracket Strut Arm Long Brace Satellite Dish, Arm Pipe Support Fits 2" Dish Masts, AT9, Part # DTVA3-Longbrace

Your price: $3.89

DIRECTV Brace Support Slimline AU9S Monopole Satellite Dish Antenna Pipe Mount Arm AU9-S Bracket Strut Arm Long Brace Satellite Dish, Arm Pipe Support Fits 2" Dish Masts, AT9, Part # DTVA3-Longbrace

The DIRECTV Slimline Multi-Satellite Dish antenna arm support bracket add-on. Mast support extends from 19" to 32" in length and accommodates both standard 2" mast supports.

Specifications:

• Extends from 19" - 32" Mast Pipe Support Arm Bracket
• Fits 2" Mast Pipes
• Easy to Install
• Bulk Packaged

Retail Price: $9.95

Our Discounted Price: $3.89

3' FT Antenna Tripod Mount Heavy Duty Channel Master 9138 3 Foot Tri-Pod Mast Mount Support CM9138 Outdoor Off-Air TV Aerial Stand-Off Kit, Part # CM-9138

Your price: $24.95

3' FT Antenna Tripod Mount Heavy Duty Channel Master 9138 3 Foot Tri-Pod Mast Mount Support CM9138 Outdoor Off-Air TV Aerial Stand-Off Kit, Part # CM-9138

This item is no longer available for purchase.

It has been replaced by the Perfect Vision Heavy Duty Tri-Pod!!!!

Channel Master - A Name You can Trust!!!

Channel Master 9138 3' FT tripod antenna mount is designed to handle up to 1 3/4" diameter masts. Perfect for camping, and sports tailgating applications.

Specifications:

• 3' FT Tripod Antenna Base Mount
• Fits up to 1 3/4" Mast Pipes
• Galvanized Steel

Retail Price: $39.95

Our Discounted Price: $24.95

Channel Master 9063 Chimney Mount Y Type Antenna Mast 12' FT 1 Pair Set of 2 Heavy Duty CM9063 Install Kit, Complete Outdoor Antenna Aerial Chimney Mounting Hardware, Stainless Steel, Part # CM-9063

Your price: $12.95

Channel Master 9063 Chimney Mount Y Type Antenna Mast 12' FT 1 Pair Set of 2 Heavy Duty CM9063 Install Kit, Complete Outdoor Antenna Aerial Chimney Mounting Hardware, Stainless Steel, Part # CM-9063

Specifications:

• (2) "Y" Chimney Mounts
• (2) 12' FT Stainless Steel Chimney Straps

Instructions:

1. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
2. Feed free end of strap through.
3. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
4. Apply strap clamps.
5. Tighten to secure straps around chimney.
6. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $29.95

Our Discounted Price: $12.95

Antenna Chimney Mount Y Type Antenna Mast 12' FT Stainless Steel Straps 1 Pair Set of 2 Heavy Duty Channel Master 9063 Install Kit, Complete Outdoor Antenna Aerial Chimney Mounting Hardware, Part # CM9063

Your price: $12.95

Antenna Chimney Mount Y Type Antenna Mast 12' FT Stainless Steel Straps 1 Pair Set of 2 Heavy Duty Channel Master 9063 Install Kit, Complete Outdoor Antenna Aerial Chimney Mounting Hardware, Part # CM9063

Specifications:

• (2) "Y" Chimney Mounts
• (2) 12' FT Stainless Steel Chimney Straps

Instructions:

1. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
2. Feed free end of strap through.
3. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
4. Apply strap clamps.
5. Tighten to secure straps around chimney.
6. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $29.95

Our Discounted Price: $12.95

Digiwave DMT-990H DiSEqC H-H Satellite Dish Rotor Positioner Motor Up To 1.2 Meter FTA One Coax Control HH Mount, DBS DSS FTA Dish Motor Mount for DiSEqC 1.2 Sat Receivers, For Up To 1.2m Dish, Part # DMT990-H

Your price: $49.95

Digiwave DMT-990H DiSEqC H-H Satellite Dish Rotor Positioner Motor Up To 1.2 Meter FTA One Coax Control HH Mount, DBS DSS FTA Dish Motor Mount for DiSEqC 1.2 Sat Receivers, For Up To 1.2m Dish, Part # DMT990-H

DiSEqC H-H Motor for Satellite Dishes Up To 1.2m!!!!

The DiSEqC H-H motor allows for the simplest installation and/or upgrade to your current satellite dish situation. It is specially designed for use with a receiver featuring DiSEqC 1.2. Its high efficiency design allows everything to be controlled via 1 coaxial cable. The compact structure, adjustable hardware limits, and ultra low noise features make this DiSEqC H-H Motor the perfect solution for satellite dishes up to 1.2m.

Specifications:

• Protocol: DiSEqC 1.2
• Compatible Receiver: DiSEqC 1.2 Receiver
• Antenna (dish) Size: 120 cm Max
• Speed 1.9 degree / sec (at 13V); 2.5 degree / sec (at 18V)
• Azimuth Angle: 75 degrees East ~ West (150 degrees Max) Adjustable
• Elevation Angle: 10 ~ 75 degrees
• Tube for Antenna: 0 55 ~ 65 mm
• Diameter of Stand-Mast: 0 35 ~ 65 mm
• Input Voltage: 13 / 18 Vdc
• Output Voltage: 13 / 18 Vdc (according to input)
• Power Consumption: 50 mA (Standby) / 200 mA (Normal) / 350 mA (Max)
• Satellite Positions: 60 Positions
• Goto "0" Position Function: Yes (Go to 0 degrees)
• Recalculation Function: Yes
• Goto X Function: Yes
• Manual Button: Yes (East / West)
• Indicating LED
• Limit Protection
  • Adjustable Hardware Limits
  • Programmable Software Limit
  • Current Limit
• Positioning Sensor: High Resolution Hall Effect Sensor

Retail Price: $79.95

Our Discounted Price: $49.95

LAVA DMT-990H DiSEqC Dish Motor 1.2 H-H Motor Positioner Satellite HH Mount, DBS DSS Satellite FTA Dish Motor Mount for DiSEqC 1.2 Sat Receivers, For Up To 1.2m Satellite Dish, Part # DMT990H

Your price: $54.95

LAVA DMT-990H DiSEqC Dish Motor 1.2 H-H Motor Positioner Satellite HH Mount, DBS DSS Satellite FTA Dish Motor Mount for DiSEqC 1.2 Sat Receivers, For Up To 1.2m Satellite Dish, Part # DMT990H

DiSEqC H-H Motor for Satellite Dishes Up To 1.2m!!!!

The DiSEqC H-H motor allows for the simplest installation and/or upgrade to your current satellite dish situation. It is specially designed for use with a receiver featuring DiSEqC 1.2. Its high efficiency design allows everything to be controlled via 1 coaxial cable. The compact structure, adjustable hardware limits, and ultra low noise features make this DiSEqC H-H Motor the perfect solution for satellite dishes up to 1.2m.

Specifications:

• Protocol: DiSEqC 1.2
• Compatible Receiver: DiSEqC 1.2 Receiver
• Antenna (dish) Size: 120 cm Max
• Speed 1.9 degree / sec (at 13V); 2.5 degree / sec (at 18V)
• Azimuth Angle: 75 degrees East ~ West (150 degrees Max) Adjustable
• Elevation Angle: 10 ~ 75 degrees
• Tube for Antenna: 0 55 ~ 65 mm
• Diameter of Stand-Mast: 0 35 ~ 65 mm
• Input Voltage: 13 / 18 Vdc
• Output Voltage: 13 / 18 Vdc (according to input)
• Power Consumption: 50 mA (Standby) / 200 mA (Normal) / 350 mA (Max)
• Satellite Positions: 60 Positions
• Goto "0" Position Function: Yes (Go to 0 degrees)
• Recalculation Function: Yes
• Goto X Function: Yes
• Manual Button: Yes (East / West)
• Indicating LED
• Limit Protection
  • Adjustable Hardware Limits
  • Programmable Software Limit
  • Current Limit
• Positioning Sensor: High Resolution Hall Effect Sensor

Retail Price: $96.95

Our Discounted Price: $54.95

Impact Acoustics Satellite Dish Level Bubble Level Red Dual Magnet Base Horizontal Vertical Axis for DBS DSS Satellite Dish Alignment TV Signal Antenna Base Pipe, North South Tool

Your price: $1.69

Impact Acoustics Satellite Dish Level Bubble Level Red Dual Magnet Base Horizontal Vertical Axis for DBS DSS Satellite Dish Alignment TV Signal Antenna Base Pipe, North South Tool

Specifications:

• Magnetic Base
• Easy to use.
• A must to install your dish mount properly.

Retail Price: $3.95

Our Discounted Price: $1.69

18' FT Chimney Mount Antenna Mast Stainless Steel Straps Y Type Heavy Duty Channel Master CM 9067 Install Kit, Complete Outdoor Off-Air Aerial Mounting Hardware, Part # CM-9067

Your price: $13.95

18' FT Chimney Mount Antenna Mast Stainless Steel Straps Y Type Heavy Duty Channel Master CM 9067 Install Kit, Complete Outdoor Off-Air Aerial Mounting Hardware, Part # CM-9067

Allows you to mount an off-air roof top TV antenna to your chimney!!!

18' FT Chimney Mounting Straps!!!!

Specifications:

• (2) "Y" Chimney Straps
• (2) 18' FT Stainless Steel Chimney Straps

Instructions:

1. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
2. Feed free end of strap through.
3. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
4. Apply strap clamps.
5. Tighten to secure straps around chimney.
6. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $24.95

Our Discounted Price: $13.95

12' FT Chimney Mount Antenna Mast Z Type Stainless Steel Straps Channel Master CM 3080 Install Kit, Complete Outdoor Off-Air Antenna Aerial Chimney Mounting Hardware, Part # CM-3080

Your price: $9.95

12' FT Chimney Mount Antenna Mast Z Type Stainless Steel Straps Channel Master CM 3080 Install Kit, Complete Outdoor Off-Air Antenna Aerial Chimney Mounting Hardware, Part # CM-3080

Allows you to mount an off-air roof top TV antenna to your chimney!!!

12' FT Chimney Mounting Straps!!!!

Specifications:

• (2) "Z" Type Chimney Straps
• (2) 12' FT Stainless Steel Chimney Straps

Instructions:

1. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
2. Feed free end of strap through.
3. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
4. Apply strap clamps.
5. Tighten to secure straps around chimney.
6. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $19.95

Our Discounted Price: $9.95

Winegard DS3000 39" Inch J-Mount DBS Satellite Dish Pipe for Antenna TV J Pipe DBS Satellite Outdoor Wall Support for Off-Air Free to Air, Rooftop Base Mast Tube, Part # DS3000

Your price: $11.95

Winegard DS3000 39" Inch J-Mount DBS Satellite Dish Pipe for Antenna TV J Pipe DBS Satellite Outdoor Wall Support for Off-Air Free to Air, Rooftop Base Mast Tube, Part # DS3000

Winegard’s DS-3000 J-Pipe mount is designed for outdoor antennas. Can be used on side of house or roof; mount foot can be used on either end of pipe for best mounting. Pipe galvanized steel, 39 inches long, with a wall thickness of .060 inches, 1.66" OD, E-Coated for maximum protection. Please Note: Mount is not designed for large directional antennas.

Retail Price: $29.95

Our Discounted Price: $11.95

Antenna Mast Offset Mount 2" Inch OD Universal Satellite Dish Wall Roof Deck Aerial Mount 28" J Pipe Support SUPERDMOUNT Tower for AU9S Satellite Dish and Large HD TV Antenna UHF/VHF/FM, Part # SLMTSTD

Your price: $19.95

Antenna Mast Offset Mount 2" Inch OD Universal Satellite Dish Wall Roof Deck Aerial Mount 28" J Pipe Support SUPERDMOUNT Tower for AU9S Satellite Dish and Large HD TV Antenna UHF/VHF/FM, Part # SLMTSTD

28" Heavy Duty HD TV Antenna Satellite Dish J Pipe Mount with 2" OD!!!!

Universal 28" J Pipe/Tower mount with 2" OD mount for adding large off-air antennas and satellite dish systems. Can be used on side of house or roof with large mount foot for improved stability. Galvanized steel, 28 inches long, 2" OD, E-Coated for maximum protection. If you need the extra length we have got it.

Universal Satellite Dish Roof / Wall Antenna J Pipe Mount:

• Satellite Dish Mount with 2" OD
• For use with 100 - 120 cm Satellite Dishes, and Large Directional HD TV Antennas Aerials
• Designed for Roof, Wall or Deck Antenna Dish Installations.
• Base Mount Hole Spacing: 5" x 7 7/8" (centers)
• SuperDMount

Retail Price: $39.95

Our Discounted Price: $19.95

DIRECTV AU9S Slimline Monopole Satellite Dish Antenna Pipe Mount Arm AU9-S Bracket Support Strut Arm Short Brace Satellite Dish, Arm Pipe Support Fits 2" Dish Masts, AT9, Part # DTVA3-Shortbrace

Your price: $2.95

DIRECTV AU9S Slimline Monopole Satellite Dish Antenna Pipe Mount Arm AU9-S Bracket Support Strut Arm Short Brace Satellite Dish, Arm Pipe Support Fits 2" Dish Masts, AT9, Part # DTVA3-Shortbrace

The DIRECTV Slimline Multi-Satellite Dish antenna arm support bracket add-on. Mast support extends from 12" to 20" in length and accommodates standard 2" mast supports.

Specifications:

• Extends from 12" - 20" Mast Pipe Support Arm Bracket
• Fits 2" Mast Pipes
• Easy to Install
• Bulk Packaged

Retail Price: $8.95

Our Discounted Price: $2.95

DIRECTV Brace Support Slimline AU9S Monopole Satellite Dish Antenna Pipe Mount Arm AU9-S Bracket Strut Arm Short Brace Satellite Dish, Arm Pipe Support Fits 2" Dish Masts, AT9, Part # DTVA3-Shortbrace

Your price: $2.95

DIRECTV Brace Support Slimline AU9S Monopole Satellite Dish Antenna Pipe Mount Arm AU9-S Bracket Strut Arm Short Brace Satellite Dish, Arm Pipe Support Fits 2" Dish Masts, AT9, Part # DTVA3-Shortbrace

The DIRECTV Slimline Multi-Satellite Dish antenna arm support bracket add-on. Mast support extends from 12" to 20" in length and accommodates standard 2" mast supports.

Specifications:

• Extends from 12" - 20" Mast Pipe Support Arm Bracket
• Fits 2" Mast Pipes
• Easy to Install
• Bulk Packaged

Retail Price: $8.95

Our Discounted Price: $2.95

Winegard DS-2016 Universal Pipe Mount Off-Air 28" Inch Antenna and Satellite Wall Roof Base J Pipe DS2016 TV Aerial Offset Support DS2000 Tower Roof Top Tube, Part # DS2016

Your price: $12.89

Winegard DS-2016 Universal Pipe Mount Off-Air 28" Inch Antenna and Satellite Wall Roof Base J Pipe DS2016 TV Aerial Offset Support DS2000 Tower Roof Top Tube, Part # DS2016

Winegard - Clearly the Worlds Best!!!

Winegard’s DS-2016 Universal Pipe/Tower mount is a quick and economical mount for adding compact off-air antennas to your digital satellite system. Can be used on side of house or roof; mount foot can be used on either end of pipe for best mounting. With U-Bolts included, it is quickly adaptable to many different pole installation. Pipe galvanized steel, 28 inches long, with a wall thickness of .060 inches, 1.66" OD, E-Coated for maximum protection. If you need the extra length we have got it. (Please Note: Not designed for large antennas.)

Retail Price: $29.95

Our Discounted Price: $12.89

Winegard SC-8000 Digital Satellite Compass SC8000 Smallest Digital Directional Compass Angle Finder North South Satellite Dish Antenna Positioning Tool, Part # SC-8000

Your price: $22.85

Winegard SC-8000 Digital Satellite Compass SC8000 Smallest Digital Directional Compass Angle Finder North South Satellite Dish Antenna Positioning Tool, Part # SC-8000

Winegard - Clearly the World's Best!!!

The Winegard SC-8000 is the wolds smallest digital compass. a portable solution to accurate compass readings for satellite installation.

Specifications:

• Great for RVs and other mobile satellite setups.
• High Accuracy
• Water Resistant
• Low power consumption and variable automatic shut off to save battery life.
• Variable gain control lets you fine tune the satellite for the best possible alignment.
• Worlds smallest and lightest digital satellite finder compass.
• Easy-to-Ready LCD display.
• Includes: Neck cord, Key ring clip, Lithium battery, and digital compass

Retail Price: $39.95

Our Discounted Price: $22.85

DIRECTV Antenna Dish Satellite Offset Mount Mast 2" Inch OD Universal Wall Roof Deck Aerial Mount 28" J Pipe Support SUPERDMOUNT Tower for AU9S Dish and Large HD TV Antenna UHF/VHF/FM, Part # SLMTSTD

Your price: $19.95

DIRECTV Antenna Dish Satellite Offset Mount Mast 2" Inch OD Universal Wall Roof Deck Aerial Mount 28" J Pipe Support SUPERDMOUNT Tower for AU9S Dish and Large HD TV Antenna UHF/VHF/FM, Part # SLMTSTD

28" Heavy Duty HD TV Antenna Satellite Dish J Pipe Mount with 2" OD!!!!

Universal 28" J Pipe/Tower mount with 2" OD mount for adding large off-air antennas and satellite dish systems. Can be used on side of house or roof with large mount foot for improved stability. Galvanized steel, 28 inches long, 2" OD, E-Coated for maximum protection. If you need the extra length we have got it.

Universal Satellite Dish Roof / Wall Antenna J Pipe Mount:

• Satellite Dish Mount with 2" OD
• For use with 100 - 120 cm Satellite Dishes, and Large Directional HD TV Antennas Aerials
• Designed for Roof, Wall or Deck Antenna Dish Installations.
• Base Mount Hole Spacing: 5" x 7 7/8" (centers)
• SuperDMount

Retail Price: $39.95

Our Discounted Price: $19.95

Magnetic Compass Field Metal Aluminum Case 1.5" Inch Highly Magnetic Directional Round 1 1/2" Direction Finder In Silver Metal Case, Install Off-Air Satellite Dish HDTV Antenna Positioning Tool, Polarity Device

Your price: $1.25

Magnetic Compass Field Metal Aluminum Case 1.5" Inch Highly Magnetic Directional Round 1 1/2" Direction Finder In Silver Metal Case, Install Off-Air Satellite Dish HDTV Antenna Positioning Tool, Polarity Device

• 1 1/2" Compass, a must have for DBS installation kit
• Used in initial dish positioning
• A must have to install your dish properly.

Retail Price: $2.95

Our Discounted Price: $1.25

PCT Channel Master 3092 Tri-Pod Tower Antenna Base 3' FT Kit Mast Support Tripod Heavy Duty Antenna Mast Support Mount Outdoor Off-Air TV Aerial Stand-Off Kit with Pitch Pads and Lag Bolts, Part # CM3092

Your price: $26.95

PCT Channel Master 3092 Tri-Pod Tower Antenna Base 3' FT Kit Mast Support Tripod Heavy Duty Antenna Mast Support Mount Outdoor Off-Air TV Aerial Stand-Off Kit with Pitch Pads and Lag Bolts, Part # CM3092

Lag Bolts and Pitch Pads Included Free for Easy Installation!!!

Channel Master 3092 tripod antenna mount is designed to handle up to 1 3/4" diameter masts. Lag bolts and pitch pads are furnished to secure the mount to your roof.

Specifications:

• Heavy Duty 3' FT Tripod Antenna Mount
• Fits up to 1 3/4" Mast Pipes
• Lag Bolts Included
• Pitch Pads Included
• Galvanized Steel

Retail Price: $46.95

Our Discounted Price: $26.95

Philips / Gemini TV Chimney Mount Kit Includes 8 Eye Bolts Nuts 8 Lock Washers 2 10' FT Galvanized Steel Straps Brackets Support Complete Outdoor Off-Air Local Signal Mounting Hardware, Part # PH- 61411

Your price: $12.95

Philips / Gemini TV Chimney Mount Kit Includes 8 Eye Bolts Nuts 8 Lock Washers 2 10' FT Galvanized Steel Straps Brackets Support Complete Outdoor Off-Air Local Signal Mounting Hardware, Part # PH- 61411

Allows you to mount an off-air roof top TV antenna to your chimney!!!

10' FT Chimney Mounting Straps!!!!

Tools needed: adjustable wrench or socket set.

Instructions:

1. Assemble straps with factory assembled eye-bolt bracket as shown.
2. Insert an eye-bolt into each bracket and thread nut onto about 1/2" from bolt to end.
3. Put bracket on chimney and run strap round chimney, being careful not to twist it. Install brackets as far apart as possible, 20 % of mast length is suggested.
4. Feed free end of strap through eye-bolt supplied.
5. Pull strap tight around chimney. Be sure the strap is evenly placed around the chimney.
6. Apply strap clamps.
7. Tighten eye-bolt nuts to secure strap around chimney.
8. Install antenna mast. Use guy wire if mast length is excessive.

Retail Price: $18.95

Our Discounted Price: $12.95

Steren 221-110 DBS Satellite Dish Roof Mount Non-Penetrating Ideal for Dish Antennas upto 24" Inch, Satellite Dish Antenna Base, Flat Steel Square Frame Support, Part # 221110

Your price: $26.89

Steren 221-110 DBS Satellite Dish Roof Mount Non-Penetrating Ideal for Dish Antennas upto 24" Inch, Satellite Dish Antenna Base, Flat Steel Square Frame Support, Part # 221110

Non-Penetrating Roof Mounts solve the problems associated with flat-roof installations. They are also an alternative when a non-permanent installation is required, or one that may be moved to other sites. Base frames and post kits can be combined in various ways to support antennas up to one meter. The base frame is manufactured from 1.25" x 1.25" x 0.188" angle iron. Base frame has a seven step thermoset powder coat finish. This base is PRE-DRILLED to fit most antenna bases. The roof mount is for 46 and 60 cm antennas with mounting feet. Single base frame covers approximately six square feet. 25.5" x 37.5" square.

Please Note: Pole Mount and Rubber Mat not included. This listing is for the purchase of the Base Section Only.

Retail Price: $59.95

Our Discounted Price: $26.89

Winegard Non-Penetrating Roof Mount Satellite Dish Antenna Kit DS-5046 and DS-5146, Steel Square Frame Support with Antenna Post Kit, Part # DS5046, DS5146

Your price: $39.95

Winegard Non-Penetrating Roof Mount Satellite Dish Antenna Kit DS-5046 and DS-5146, Steel Square Frame Support with Antenna Post Kit, Part # DS5046, DS5146

Winegard's Non-Penetrating Roof Mounts solve the problems associated with flat-roof installations. They are also an alternative when a non-permanent installation is required, or one that may be moved to other sites. The post is steel with sturdy aluminum braces. Base frame and post have a seven step thermoset powder coat finish.

The Winegard Model Single Base Frame, for 46 and 60 cm antennas with Winegard, RCA, Sony, ITI and other mounting feet. Single base frame covers approximately six square feet. 25.5" x 37.5" square.

The Winegard Model DS-5146 Post Kit. This post will support antennas up to 76 cm when used with the single base frame. Includes pole and braces. Pole size 1.66" OD, 19" long, 16 ga steel.

Please Note: Rubber Mat not included.

Retail Price: $89.95

Our Discounted Price: $39.95

Magnetic Field Compass Highly Magnetic Needle Aluminum Case Glass Look Top Direction Polarity 1 1/4" Round Satellite Dish HDTV Antenna North South Positioning, The Angle Position Finder

Your price: $1.19

Magnetic Field Compass Highly Magnetic Needle Aluminum Case Glass Look Top Direction Polarity 1 1/4" Round Satellite Dish HDTV Antenna North South Positioning, The Angle Position Finder

• 1 1/4" Compass, a must have for DBS installation kit
• Used in initial dish positioning
• A must to install your dish properly.

Retail Price: $1.95

Our Discounted Price: $1.19

Philips Gemini SDW1411/17 Chimney Mount TV Antenna 2-10' FT Galvanized Steel Straps 2-Brackets Antenna Mast Chimney Mount Kit Philips Off-Air Signal Aerial Bracket Support with Stand-Off Mounting and Hardware Install, Part # CMK150

Your price: $10.95

Philips Gemini SDW1411/17 Chimney Mount TV Antenna 2-10' FT Galvanized Steel Straps 2-Brackets Antenna Mast Chimney Mount Kit Philips Off-Air Signal Aerial Bracket Support with Stand-Off Mounting and Hardware Install, Part # CMK150

This TV Antenna Chimney Mounting Kit contains everything you will need for either a Twin lead or Coax Cable installation.

Contains:

• 1-Set of Chimney Mount Straps and Hardware
• 4-Screw-in Standoffs
• 2-Mast Clip-on Standoffs
• 4-Coaxial F Connectors
• 1-75 ohm Outdoor Matching Transformer
• 1-75 ohm Indoor Matching Transformer
• 1-75 ohm Indoor Push-on Matching Transformer
• 2-Cable Feed Thru Bushings
• 20-Coax Nail-in Fasteners

Antenna Wire Not Included.

Retail Price: $24.95

Our Discounted Price: $10.95

Compass Lensatic Liquid Filled Metal Case Magnetic Directional Engineers for North South Map Positioning Rugged Easy Readability, Polarity Direction Finder, Part # DC453B

Your price: $4.95

Compass Lensatic Liquid Filled Metal Case Magnetic Directional Engineers for North South Map Positioning Rugged Easy Readability, Polarity Direction Finder, Part # DC453B

• Liquid Filled for Fast Reads
• Sturdy Metal Case
• Floating Luminous Dial - Easy to Read
• Adjustable Luminous Marching Line
• Thumb Hold Magnifying Viewer
• Sighting Hairline
• Ideal for locating position on a map or in the field

Retail Price: $9.95

Our Discounted Price: $4.95

Steren 200-991 Bubble Level Magnetic Base Horizontal Vertical Axis for DBS DSS Satellite Dish Alignment TV Signal Antenna Base Pipe, North South Tool, Part # 200-991

Your price: $1.49

Steren 200-991 Bubble Level Magnetic Base Horizontal Vertical Axis for DBS DSS Satellite Dish Alignment TV Signal Antenna Base Pipe, North South Tool, Part # 200-991

Specifications:

• Magnetic Base
• Easy to use.
• A must to install your dish mount properly.

Retail Price: $3.95

Our Discounted Price: $1.49

Winegard DS5146 Post Kit for 46 60 76 cm Satellite Dish Antenna Base Frame Roof Mount Pipe Support for Non-Penetrating Frame 1.66" Pole and Angle Supports, Part # DS5146

Your price: $7.95

Winegard DS5146 Post Kit for 46 60 76 cm Satellite Dish Antenna Base Frame Roof Mount Pipe Support for Non-Penetrating Frame 1.66" Pole and Angle Supports, Part # DS5146

Winegard's Non-Penetrating Roof Mounts solve the problems associated with flat-roof installations. They are also an alternative when a non-permanent installation is required, or one that may be moved to other sites. Base frames and post kits can be combined in various ways to support antennas up to one meter. The post is steel with sturdy aluminum braces. Base frame and post have a seven step thermoset powder coat finish.

This purchase is for the Winegard Model DS-5146 Post Kit. This post will support antennas up to 76 cm when used with the single base frame. Includes pole and braces. Pole size 1.66" OD, 19" long, 16 ga steel.

Retail Price: $19.95

Our Discounted Price: $7.95

Vanco Map Reading Compass with Mirror Ruler 1 3/4" Diameter Dial Lanyard Professional Map Compass Compass Magnetic Directional Map Positioning with Easy Readability, Polarity Direction Finder, Part # CC45-6

Your price: $3.49

Vanco Map Reading Compass with Mirror Ruler 1 3/4" Diameter Dial Lanyard Professional Map Compass Compass Magnetic Directional Map Positioning with Easy Readability, Polarity Direction Finder, Part # CC45-6

• Professional Grade Mapping Compass
• 1 3/4" Diameter Dial Face
• Mirror with Sighting Hairline
• Built-In Ruler
• Includes Lanyard
• Easy to Read
• Ideal for locating position on a map or in the field.

Retail Price: $8.95

Our Discounted Price: $3.49

Antenna Mast Offset Mount Satellite Dish Support Bracket MM2 TV Minimount-2 DBS Unit Mounts into Bolt Section of Satellite Antenna Quick Off-Air 28 1/4" Inch Length 1 5/16" Inch Wide, Part # MM-2

Your price: $17.95

Antenna Mast Offset Mount Satellite Dish Support Bracket MM2 TV Minimount-2 DBS Unit Mounts into Bolt Section of Satellite Antenna Quick Off-Air 28 1/4" Inch Length 1 5/16" Inch Wide, Part # MM-2

This unit mounts into the bolt section of your existing satellite dish, and allows one to mount their off-air antenna very quickly and easily. An offset pipe (approx 24 inch) is also included (but not shown) that slides into the mount that makes installation fast, easy, professional, and pleasant to the eyes.

Retail Price: $29.95

Our Discounted Price: $17.95

Steren 221-365 Large Satellite Dish Mount Clamp-On Roof Overhang Joists Patio Balcony Railings Non-Penetrating Dish Mount Antennas Base Support for up to 36" Inch Satellite Dish, Part # 221365

Your price: $50.95

Steren 221-365 Large Satellite Dish Mount Clamp-On Roof Overhang Joists Patio Balcony Railings Non-Penetrating Dish Mount Antennas Base Support for up to 36" Inch Satellite Dish, Part # 221365

Non-Pentrating Clamp-On Dish Antenna Mount

Steren’s Clamp-On Satellite Dish Mount is the best solution for quickly installing satellite dishes in homes, apartments or condominium complexes. Meeting most landlord and Home Owner Association requirements for non-penetration and no damage, it provides the best installation option ever offered. The revolutionary patented design provides exceptional versatility in dish placement, ensuring optimal satellite signal reception. The Clamp-On Mount can be attached to the premises overhang joists or eaves, avoiding ugly rooftop mounts. It is ideal in situations where traditional mounting methods are impractical including wherever drilling holes is not possible or is prohibited such as on condo or apartment balcony railings and fences.

Specifications:

• Unique clamp-on design greatly simplifies and reduces satellite dish installation time
• Clamps directly to roof overhangs, joists, patio/balcony railings or fences
• Penetration-free attachment ensures no damage to structures
• Avoids damage claims from most landlords and HOAs (Home Owner Associations)
• Ideal for satellite dishes from 18 to 36 inches
• Universal mount options provide mounting for the best possible satellite signal reception
• Attaches to any solid structure made of wood or metal up to 3˝ wide
• Fast and easy installation or removal, using ordinary hand tools, allows dish relocation with tenants
• Constructed of heavy gauge steel and coated for durability in the harshest environments
• Mounting plate features multiple hole-patterns for compatibility with any type or size of home satellite dish
• Includes all necessary installation hardware plus easy-to-follow instructions

Retail Price: $89.95

Our Discounted Price: $50.95

Steren 221-360 Small Satellite Dish Mount Clamp-On Roof Overhang Joists Patio Balcony Rails Non-Penetrating Dish Mount Antennas Base Support for up to 24" Inch Satellite Dish, Part # 221360

Your price: $30.95

Steren 221-360 Small Satellite Dish Mount Clamp-On Roof Overhang Joists Patio Balcony Rails Non-Penetrating Dish Mount Antennas Base Support for up to 24" Inch Satellite Dish, Part # 221360

Non-Pentrating Clamp-On Dish Antenna Mount

Steren’s Clamp-On Satellite Dish Mount is the best solution for quickly installing satellite dishes in homes, apartments or condominium complexes. Meeting most landlord and Home Owner Association requirements for non-penetration and no damage, it provides the best installation option ever offered. The revolutionary patented design provides exceptional versatility in dish placement, ensuring optimal satellite signal reception. The Clamp-On Mount can be attached to the premises overhang joists or eaves, avoiding ugly rooftop mounts. It is ideal in situations where traditional mounting methods are impractical including wherever drilling holes is not possible or is prohibited such as on condo or apartment balcony railings and fences.

Specifications:

• Unique clamp-on design greatly simplifies and reduces satellite dish installation time
• Clamps directly to roof overhangs, joists, patio/balcony railings or fences
• Penetration-free attachment ensures no damage to structures
• Avoids damage claims from most landlords and HOAs (Home Owner Associations)
• Ideal for satellite dishes up to 24 inches
• Universal mount options provide mounting for the best possible satellite signal reception
• Attaches to any solid structure made of wood or metal up to 3˝ wide
• Fast and easy installation or removal, using ordinary hand tools, allows dish relocation with tenants
• Constructed of heavy gauge steel and coated for durability in the harshest environments
• Mounting plate features multiple hole-patterns for compatibility with any type or size of home satellite dish
• Includes all necessary installation hardware plus easy-to-follow instructions

Retail Price: $59.95

Our Discounted Price: $39.95