Winegard UT-2700 UHF Signal Trap Adjustable TV Antenna Off-Air Outdoor Aerial Frequency Blocker, Variable Tune Range, Channel Adjacent, AC / DC Passive, Part # UT2700

Your price: $68.89

Winegard UT-2700 UHF Signal Trap Adjustable TV Antenna Off-Air Outdoor Aerial Frequency Blocker, Variable Tune Range, Channel Adjacent, AC / DC Passive, Part # UT2700

UT-2700 ADJUSTABLE UHF TRAP - UHF trap than may be tuned over the frequency range of 470 to 810 MHz. Features two separate traps that may both be tuned to the same frequency to reduce it -15 dB, or to separate frequencies to reduce them 8.5 dB. The UT-2700 may be mounted indoors or outside. Passes VHF frequency, AC/DC passive.

Retail Price: $89.95

Our Discounted Price: $68.89

Winegard FT-3000 FM Signal Trap Antenna 300 Ohm FT3000 Video Outdoor Local Radio Station Band Attenuator for Aerial Frequency Filter Overload Blocker, Part # FT3000

Your price: $14.89

Winegard FT-3000 FM Signal Trap Antenna 300 Ohm FT3000 Video Outdoor Local Radio Station Band Attenuator for Aerial Frequency Filter Overload Blocker, Part # FT3000

FT-3000 FM TRAP Fixed FM trap designed to attenuate the entire FM band -25 dB. AC/DC passive. UHF passive. Housed in a rugged plastic weatherproof housing for mounting on antenna mast or boom. Input and output connections through 300 ohm no-strip Malco-type terminals. Shipped with mounting bracket and hardware.

Our Discounted Price: $14.89

Winegard FT-7500 FM Signal Trap Antenna 75 Ohm FT7500 Video Outdoor Radio Station Band Attenuator for Aerial Frequency Filter Overload Blocker, Part # FT7500

Your price: $22.95

Winegard FT-7500 FM Signal Trap Antenna 75 Ohm FT7500 Video Outdoor Radio Station Band Attenuator for Aerial Frequency Filter Overload Blocker, Part # FT7500

This product is no longer available for purchase.

It has been replaced by the Winegard FT-7500 FM Signal Trap!!!!

FT-7500 TRAP (INDOOR/OUTDOOR) Fixed 75 ohm FM trap designed to attenuate the entire FM band an average of -26 dB. The FM-7500 is AC/DC passive and reduces strong signals from local FM stations to prevent amplifier and TV set overload. Not recommended for receiving TV Channel 6.

Retail Price: $39.95

Our Discounted Price: $22.95

Winegard FT-7600 FM Signal Trap TV Antenna Variable Frequency 26 dB DC Passive Outdoor Off-Air Aerial, Tune Adjustable, Attenuate Channels, Part # FT7600

Your price: $18.95

Winegard FT-7600 FM Signal Trap TV Antenna Variable Frequency 26 dB DC Passive Outdoor Off-Air Aerial, Tune Adjustable, Attenuate Channels, Part # FT7600

FT-7600 VARIABLE FM TRAP (75 ohm) * Two stage variable FM trap designed to attenuate stations in the FM band (88 to 108 MHz) When both stages are tuned to a single frequency, it will be attenuated 26 dB or about 1/20 of its previous level. When each stage is tuned to a different frequency, it will be reduced from 7 to 10 dB or 1/2 to 1/3 of the original level. The FT-7600 is used to reduce strong signals from local FM stations and prevent overload of amplifier and TV sets. Unit is enclosed in a weatherproof housing for mounting on antenna boom, mast or wall. FT-7600 will pass power to an antenna-mounted preamplifier. Mounting hardware, F-connectors included.

Retail Price: $38.95

Our Discounted Price: $18.95

Winegard VF-4000 Signal Filter TV Antenna VHF Channel 4 Frequency Aerial Off-Air, Satellite Receiver Distribution VCR Coupler, Deep Fringe 75 Ohm Cable, AC / DC Passive Output, Part # VF4000

Your price: $19.95

Winegard VF-4000 Signal Filter TV Antenna VHF Channel 4 Frequency Aerial Off-Air, Satellite Receiver Distribution VCR Coupler, Deep Fringe 75 Ohm Cable, AC / DC Passive Output, Part # VF4000

VF-4000 FILTER (VHF) Filters pass channel 4 from satellite receiver or VCR and eliminate all other channels which may pass through the satellite receiver or VCR when not in use. Coupling input provided for antenna where adjacent channels are not present. Not AC/DC passive. Channel of output VF-4000 = Chan. 4.

Retail Price: $29.95

Our Discounted Price: $19.95

F-Type DC Block Coaxial Coupler IR DC Voltage Block Female to Male 1 Pack for IR Over Coax Cable Systems F Connector Audio Video AC/DC Volt Blocking Connector, Part # Channel Master 7264

Your price: $1.19

F-Type DC Block Coaxial Coupler IR DC Voltage Block Female to Male 1 Pack for IR Over Coax Cable Systems F Connector Audio Video AC/DC Volt Blocking Connector, Part # Channel Master 7264

The Channel Master 7264 DC Block has a female and male F type coaxial connection. Simply insert into the line to block DC current from passing through while permitting RF Power to flow. Single 1 Pack.

Specifications:

• Channel Master Voltage Block
• AC Voltage Block: 60 Volt
• DC Voltage Block: 48 Volt
• Female to Male Coaxial Connection
• Blocks Unwanted Voltage to Specific TV Locations.
• Sold as Singles

Retail Price: $2.95

Our Discounted Price: $1.19

Winegard VB-1000 DC Voltage Block for 75 Ohm F-Connector Voltage Block Female to Male 1 Pack Coaxial Coupler for IR Over Coax Cable Systems Audio Video AC/DC Volt Blocking Adapter Connector, Part # VB1000

Your price: $1.95

Winegard VB-1000 DC Voltage Block for 75 Ohm F-Connector Voltage Block Female to Male 1 Pack Coaxial Coupler for IR Over Coax Cable Systems Audio Video AC/DC Volt Blocking Adapter Connector, Part # VB1000

The Winegard DC Block has a female and male F type coaxial connection. Simply insert into the line to block DC current from passing through while permitting RF Power to flow. Single 1 Pack.

Specifications:

• Winegard F Voltage Block
• Insertion Loss: .75 dB Max
• Frequency Range: 5 - 1750 MHz
• Used to block voltage from in-line power inserters.
• Sold as Singles

Retail Price: $3.95

Our Discounted Price: $1.95

DC Voltage Block Connector Adapter 75 Ohm F-Type Winegard VB-1000 Voltage Block Female to Male 1 Pack Coaxial Coupler for IR Over Coax Cable Systems Audio Video AC/DC Volt Blocking Adapter Connector, Part # VB1000

Your price: $1.95

DC Voltage Block Connector Adapter 75 Ohm F-Type Winegard VB-1000 Voltage Block Female to Male 1 Pack Coaxial Coupler for IR Over Coax Cable Systems Audio Video AC/DC Volt Blocking Adapter Connector, Part # VB1000

The Winegard DC Block has a female and male F type coaxial connection. Simply insert into the line to block DC current from passing through while permitting RF Power to flow. Single 1 Pack.

Specifications:

• Winegard F Voltage Block
• Insertion Loss: .75 dB Max
• Frequency Range: 5 - 1750 MHz
• Used to block voltage from in-line power inserters.
• Sold as Singles

Retail Price: $3.95

Our Discounted Price: $1.95

Channel 4 Signal Filter VHF TV Antenna Winegard VF-4000 Aerial Off-Air, Satellite Receiver Distribution VCR Coupler, Deep Fringe 75 Ohm Cable, AC / DC Passive Output, Part # VF4000

Your price: $19.95

Channel 4 Signal Filter VHF TV Antenna Winegard VF-4000 Aerial Off-Air, Satellite Receiver Distribution VCR Coupler, Deep Fringe 75 Ohm Cable, AC / DC Passive Output, Part # VF4000

VF-4000 FILTER (VHF) Filters pass channel 4 from satellite receiver or VCR and eliminate all other channels which may pass through the satellite receiver or VCR when not in use. Coupling input provided for antenna where adjacent channels are not present. Not AC/DC passive. Channel of output VF-4000 = Chan. 4.

Retail Price: $29.95

Our Discounted Price: $19.95

Channel Plus TC-200A Tilt Compensator 1 Pack F-Connector High Frequency Attenuator TC200A In-Line Filter Female to Male Coupler with Female to Female Barrel Adapter, Part # TC-200A

Your price: $10.49

Channel Plus TC-200A Tilt Compensator 1 Pack F-Connector High Frequency Attenuator TC200A In-Line Filter Female to Male Coupler with Female to Female Barrel Adapter, Part # TC-200A

Channel Plus TC-200A In-Line High Frequency Tilt Compensator

The Model TC-200A Tilt Compensator is an in-line filter designed to create an attenuation loss equal and opposite to cable loss. Coaxial cable attenuates high frequencies greater than low frequencies. This problem is most severe when cascading amplifiers one after another. The signal differences are attenuated to a point where the high frequency signals are so small compared to the low frequency signals that the high frequency signals can no longer be received. The TC-200A Tilt Compensator provides a balanced signal level by compensating for 200 feet of coax cable loss and allowing all signal levels on all channels to be of equal amplitude at distant locations. Therefore, the picture quality on the higher channels will be maintained.

The TC-200A is designed to work with RG-6 coax cable carrying signals in the 5 MHz to 1 GHz range. When an RG-6 cable run reaches 200 feet, install a TC-200A Tilt Compensator whenever an amplifier stage follows. A female barrel connector is included with the TC-200A for in-line applications. The TC-200A is non-directional, the input can be connected to either end.

Specifications:

• Compensates for high frequency signal loss on long coax runs
• Female "F" and male "F" connectors
• Includes Female-Female barrel connector for in-line use

Retail Price: $19.95

Our Discounted Price: $10.49

Winegard FT7600 Two Stage Variable FM Trap Attenuates FM Band Stations 88 to 108 MHz TV Antenna Frequency 26 dB DC Passive Outdoor Off-Air Aerial, Part # FT7600

Your price: $18.95

Winegard FT7600 Two Stage Variable FM Trap Attenuates FM Band Stations 88 to 108 MHz TV Antenna Frequency 26 dB DC Passive Outdoor Off-Air Aerial, Part # FT7600

FT-7600 VARIABLE FM TRAP (75 ohm) Two stage variable FM trap designed to attenuate stations in the FM band (88 to 108 MHz) When both stages are tuned to a single frequency, it will be attenuated 26 dB or about 1/20 of its previous level. When each stage is tuned to a different frequency, it will be reduced from 7 to 10 dB or 1/2 to 1/3 of the original level. The FT-7600 is used to reduce strong signals from local FM stations and prevent overload of amplifier and TV sets. Unit is enclosed in a weatherproof housing for mounting on antenna boom, mast or wall. FT-7600 will pass power to an antenna-mounted preamplifier. Mounting hardware, F-connectors included.

Retail Price: $38.95

Our Discounted Price: $18.95

Winegard TA8700 Variable Attenuator 0-18 dB Off-Air Antenna TA-8700 Variable UHF/VHF Attenuator Pad 75 Ohm AC/DC Passive 1 Amp 24 Volts Max Aerial Signal Strength Filter, Part # TA8700

Your price: $18.95

Winegard TA8700 Variable Attenuator 0-18 dB Off-Air Antenna TA-8700 Variable UHF/VHF Attenuator Pad 75 Ohm AC/DC Passive 1 Amp 24 Volts Max Aerial Signal Strength Filter, Part # TA8700

Winegard - Clearly the World's Best!!!

Winegard's TA-8700 is a 75 Ohm variable attenuator designed to cover the frequency range of 5 to 1000 MHz. The TA-8700 provides continuously variable attenuation from 1-17 dB. The unit is AC-DC passive to allow remote amplifiers to be powered thru it. Connectors are standard F-type.

Specifications:

•  Winegard TA-8700 Variable Attenuator
• AC-DC Passive
• 1 Amp, 24 Volts Max

Our Discounted Price: $18.95

Winegard ST7700 Selectable Isolation Line Tap-Off 75 Ohm F Type Ivory Insert, Low Insertion Loss, Isolation Values of 12 dB 15 dB and 20 dB, Fits Standard Electrical Outlet Face Plate, Part # ST-7700

Your price: $6.95

Winegard ST7700 Selectable Isolation Line Tap-Off 75 Ohm F Type Ivory Insert, Low Insertion Loss, Isolation Values of 12 dB 15 dB and 20 dB, Fits Standard Electrical Outlet Face Plate, Part # ST-7700

Winegard - Clearly the World's Best!!!

Winegard's ST-7700 82 Channel Selectable Isolation Line Tap-Off features low insertion loss and excellent VSWR. Isolation values of 12, 15, and 20 dB are available in each unit. Select the isolation value desired by snipping resistor lead on back of tap when installing.

Specifications:

• Winegard ST7700 Line Tap-Off
• Selectable Isolation with Low Insertion Loss
• 12, 15, 20 dB and Signal Isolation Values
• AC-DC Passive

Our Discounted Price: $6.95

Steren 201-500 DC Voltage Blocking Coupler 5 - 1750 MHz Connector 2 GHz Female to Male Nickle Plate Insertion Loss 0.3 dB Voltage Block 1 Pack Coaxial Coupler Audio Video AC/DC Volt Blocking Adapter Connector, Part # 201500

Your price: $1.29

Steren 201-500 DC Voltage Blocking Coupler 5 - 1750 MHz Connector 2 GHz Female to Male Nickle Plate Insertion Loss 0.3 dB Voltage Block 1 Pack Coaxial Coupler Audio Video AC/DC Volt Blocking Adapter Connector, Part # 201500

This item is no longer available for purchase.

It has been replaced by the Winegard VB-1000 Voltage Block!!!!

The Steren DC Block has a female and male F type coaxial connection. Simply insert into the line to block DC current from passing through while permitting RF Power to flow. Single 1 Pack.

Specifications:

• Steren 201-500 F Voltage Block
• Insertion Loss: .03 dB
• Return Loss: 16 dB
• Frequency Range: 5 - 1750 MHz
• Used to block voltage from in-line power inserters.
• Sold as Singles

Retail Price: $3.95

Our Discounted Price: $1.29

Channel Plus NF-469 Notch Filter Blocks CATV Channels 64 - 70 and UHF 14 - 19 NF469 Creates 3 Modulation Channels 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-469

Your price: $23.75

Channel Plus NF-469 Notch Filter Blocks CATV Channels 64 - 70 and UHF 14 - 19 NF469 Creates 3 Modulation Channels 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-469

Channel Plus NF-469 Notch Filter

The Model NF-469 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-469 filters out channels to make room for modulated channels. In addition, the NF-469 blocks the modulated signals from being broadcast back into the coax. The NF-469 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

The Model NF-469 Notch Filter blocks incoming CATV channels 64-70 and off-air UHF TV channels 14-19, allowing 5400, 5500, and SVM series modulators to insert TV channels without interference. Please Note: To avoid interference, be sure there's an empty channel on each side of a modulated channel.

Specifications:

• Notch filter frequency 469.25 MHz to 497.25 MHz
• Rejects CATV channels 64 to 70
• Allows insertion of CATV channels 65, 66, 67, 68, & 69
• Rejects off-air UHF TV channels 14 to 19
• Allows insertion of UHF TV channels 15, 16, 17, & 18
• Dimensions: 3.25" L x 1 W"

Retail Price: $39.95

Our Discounted Price: $23.75

Channel Plus NF-470 Notch Filter Blocks CATV Channels 70 - 74 and UHF 19 - 23 Creates CATV 71 - 73 NF470 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-470

Your price: $24.75

Channel Plus NF-470 Notch Filter Blocks CATV Channels 70 - 74 and UHF 19 - 23 Creates CATV 71 - 73 NF470 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-470

Channel Plus NF-470 Notch Filter

The Model NF-470 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-470 filters out channels to make room for modulated channels. In addition, the NF-470 blocks the modulated signals from being broadcast back into the coax. The NF-470 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

The Model NF-470 Notch Filter blocks incoming CATV channels 70-74 and off-air UHF TV channels 19-23, allowing 5400, 5500, and SVM series modulators to insert TV channels without interference. Please Note: To avoid interference, be sure there's an empty channel on each side of a modulated channel.

Specifications:

• Notch filter frequency 499.25 MHz to 523.25 MHz
• Rejects CATV channels 70 to 74
• Allows insertion of CATV channels 71, 72, & 73
• Rejects off-air UHF TV channels 19 to 23
• Allows insertion of UHF TV channels 20, 21, & 22
• Dimensions: 3.25" L x 1 W"

Retail Price: $39.95

Our Discounted Price: $24.75

Channel Plus NF-471 Notch Filter Blocks CATV Channels 75 - 80 and UHF 24 - 29 Creates CATV 76 - 79 NF471 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-471

Your price: $25.25

Channel Plus NF-471 Notch Filter Blocks CATV Channels 75 - 80 and UHF 24 - 29 Creates CATV 76 - 79 NF471 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-471

Channel Plus NF-471 Notch Filter

The Model NF-471 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-471 filters out channels to make room for modulated channels. In addition, the NF-471 blocks the modulated signals from being broadcast back into the coax. The NF-471 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

The Model NF-471 Notch Filter blocks incoming CATV channels 75-80 and off-air UHF TV channels 24-29, allowing 5400, 5500, and SVM series modulators to insert TV channels without interference. Please Note: To avoid interference, be sure there's an empty channel on each side of a modulated channel.

Specifications:

• Notch filter frequency 529.25 MHz to 559.25 MHz
• Rejects CATV channels 75 to 80
• Allows insertion of CATV channels 76, 77, 78, & 79
• Rejects off-air UHF TV channels 24 to 29
• Allows insertion of UHF TV channels 25, 26, 27, & 28
• Dimensions: 3.25" L x 1 W"

Retail Price: $39.95

Our Discounted Price: $25.25

Channel Plus LPF-750 Low Pass Filter Channels 2 - 116 Removes CATV Channels Above the Pass Band 750 MHz LPF750 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-750

Your price: $29.85

Channel Plus LPF-750 Low Pass Filter Channels 2 - 116 Removes CATV Channels Above the Pass Band 750 MHz LPF750 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-750

Channel Plus LPF-750 Low Pass Filter

The Model LPF-750 Low-pass Filter is used on systems when broadband entertainment feed is supplied by a CATV service. The filter removes all CATV channels above the pass band, allowing insertion of locally-generated Channel Plus modulated channels. In addition, the filter removes cable system noise which degrades the picture quality of the locally-generated channels.

Specifications:

• 0 to 750 MHz bandpass frequency
• Passes off-air TV channels 2 to 60
• Passes CATV channels 2 to 116
• Allows insertion of TV channels 65 to 69
• Allows insertion of CATV channels 121 to 125

Retail Price: $49.95

Our Discounted Price: $29.85

Channel Master 7264 F-Type DC Voltage Block Adapter Coaxial Coupler Female to Male 1 Pack for IR Over Coax Cable Systems F Connector Audio Video AC/DC Volt Blocking Connector, Part # 7264

Your price: $1.14

Channel Master 7264 F-Type DC Voltage Block Adapter Coaxial Coupler Female to Male 1 Pack for IR Over Coax Cable Systems F Connector Audio Video AC/DC Volt Blocking Connector, Part # 7264

The Channel Master 7264 DC Block has a female and male F type coaxial connection. Simply insert into the line to block DC current from passing through while permitting RF Power to flow. Single 1 Pack.

Specifications:

• Channel Master Voltage Block
• AC Voltage Block: 60 Volt
• DC Voltage Block: 48 Volt
• Female to Male Coaxial Connection
• Blocks Unwanted Voltage to Specific TV Locations.
• Sold as Singles

Retail Price: $2.95

Our Discounted Price: $1.14

RV Line Tap-Off 75 Ohm Selectable Isolation Ivory Duplex Outlet Winegard ST7700 F Type Ivory Insert, Low Insertion Loss, Isolation Values of 12 dB 15 dB and 20 dB, Fits Standard Electrical Outlet Face Plate, Part # ST-7700

Your price: $6.95

RV Line Tap-Off 75 Ohm Selectable Isolation Ivory Duplex Outlet Winegard ST7700 F Type Ivory Insert, Low Insertion Loss, Isolation Values of 12 dB 15 dB and 20 dB, Fits Standard Electrical Outlet Face Plate, Part # ST-7700

Winegard - Clearly the World's Best!!!

Winegard's ST-7700 82 Channel Selectable Isolation Line Tap-Off features low insertion loss and excellent VSWR. Isolation values of 12, 15, and 20 dB are available in each unit. Select the isolation value desired by snipping resistor lead on back of tap when installing.

Specifications:

• Winegard ST7700 Line Tap-Off
• Selectable Isolation with Low Insertion Loss
• 12, 15, 20 dB and Signal Isolation Values
• AC-DC Passive

Our Discounted Price: $6.95

Steren 201-406 6 dB Inline Attenuator DC Block F to Male Nickle Plated Coupler 5 - 1750 MHz Connector Female to Male 1 Pack Coaxial Coupler Audio Video Adapter Connector, Part # 201-406

Your price: $0.97

Steren 201-406 6 dB Inline Attenuator DC Block F to Male Nickle Plated Coupler 5 - 1750 MHz Connector Female to Male 1 Pack Coaxial Coupler Audio Video Adapter Connector, Part # 201-406

The Steren 201-406 Inline 6 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Steren 201-406 Female to Male 6 dB Inline Attenuator Pads
• Frequency Range: 5 - 1750 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $1.95

Our Discounted Price: $0.97

Linear LPF-750 Low Pass Filter Channels 2 - 116 Removes CATV Channels Above the Pass Band 750 MHz LPF750 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-750

Your price: $29.85

Linear LPF-750 Low Pass Filter Channels 2 - 116 Removes CATV Channels Above the Pass Band 750 MHz LPF750 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-750

Linear LPF-750 Low Pass Filter

The Model LPF-750 Low-pass Filter is used on systems when broadband entertainment feed is supplied by a CATV service. The filter removes all CATV channels above the pass band, allowing insertion of locally-generated Channel Plus modulated channels. In addition, the filter removes cable system noise which degrades the picture quality of the locally-generated channels.

Specifications:

• 0 to 750 MHz bandpass frequency
• Passes off-air TV channels 2 to 60
• Passes CATV channels 2 to 116
• Allows insertion of TV channels 65 to 69
• Allows insertion of CATV channels 121 to 125

Retail Price: $49.95

Our Discounted Price: $29.85

Linear NF-471 Notch Filter Blocks CATV Channels 75 - 80 and UHF 24 - 29 Creates CATV 76 - 79 NF471 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-471

Your price: $25.25

Linear NF-471 Notch Filter Blocks CATV Channels 75 - 80 and UHF 24 - 29 Creates CATV 76 - 79 NF471 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-471

Linear NF-471 Notch Filter

The Model NF-471 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-471 filters out channels to make room for modulated channels. In addition, the NF-471 blocks the modulated signals from being broadcast back into the coax. The NF-471 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

The Model NF-471 Notch Filter blocks incoming CATV channels 75-80 and off-air UHF TV channels 24-29, allowing 5400, 5500, and SVM series modulators to insert TV channels without interference. Please Note: To avoid interference, be sure there's an empty channel on each side of a modulated channel.

Specifications:

• Notch filter frequency 529.25 MHz to 559.25 MHz
• Rejects CATV channels 75 to 80
• Allows insertion of CATV channels 76, 77, 78, & 79
• Rejects off-air UHF TV channels 24 to 29
• Allows insertion of UHF TV channels 25, 26, 27, & 28
• Dimensions: 3.25" L x 1 W"

Retail Price: $39.95

Our Discounted Price: $25.25

Linear NF-469 Notch Filter Blocks CATV Channels 64 - 70 and UHF 14 - 19 NF469 Creates 3 Modulation Channels 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-469

Your price: $23.75

Linear NF-469 Notch Filter Blocks CATV Channels 64 - 70 and UHF 14 - 19 NF469 Creates 3 Modulation Channels 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-469

Linear NF-469 Notch Filter

The Model NF-469 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-469 filters out channels to make room for modulated channels. In addition, the NF-469 blocks the modulated signals from being broadcast back into the coax. The NF-469 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

The Model NF-469 Notch Filter blocks incoming CATV channels 64-70 and off-air UHF TV channels 14-19, allowing 5400, 5500, and SVM series modulators to insert TV channels without interference. Please Note: To avoid interference, be sure there's an empty channel on each side of a modulated channel.

Specifications:

• Notch filter frequency 469.25 MHz to 497.25 MHz
• Rejects CATV channels 64 to 70
• Allows insertion of CATV channels 65, 66, 67, 68, & 69
• Rejects off-air UHF TV channels 14 to 19
• Allows insertion of UHF TV channels 15, 16, 17, & 18
• Dimensions: 3.25" L x 1 W"

Retail Price: $39.95

Our Discounted Price: $23.75

Linear NF-470 Notch Filter Blocks CATV Channels 70 - 74 and UHF 19 - 23 Creates CATV 71 - 73 NF470 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-470

Your price: $24.75

Linear NF-470 Notch Filter Blocks CATV Channels 70 - 74 and UHF 19 - 23 Creates CATV 71 - 73 NF470 1 Pack In-Line Notch Filter Coupler Barrel Adapter, Part # NF-470

Linear NF-470 Notch Filter

The Model NF-470 Notch Filter couples the incoming signal source coax cable to the input on a splitter or bi-directional DA-series amplifier. Once installed, the NF-470 filters out channels to make room for modulated channels. In addition, the NF-470 blocks the modulated signals from being broadcast back into the coax. The NF-470 is a perfect solution for modulation in the ever-increasing bandwidth taken up by Cable Television (CATV).

The Model NF-470 Notch Filter blocks incoming CATV channels 70-74 and off-air UHF TV channels 19-23, allowing 5400, 5500, and SVM series modulators to insert TV channels without interference. Please Note: To avoid interference, be sure there's an empty channel on each side of a modulated channel.

Specifications:

• Notch filter frequency 499.25 MHz to 523.25 MHz
• Rejects CATV channels 70 to 74
• Allows insertion of CATV channels 71, 72, & 73
• Rejects off-air UHF TV channels 19 to 23
• Allows insertion of UHF TV channels 20, 21, & 22
• Dimensions: 3.25" L x 1 W"

Retail Price: $39.95

Our Discounted Price: $24.75

Linear TC-200A Tilt Compensator TC200A 1 Pack F-Connector High Frequency Attenuator In-Line Filter Female to Male Coupler with Female to Female Barrel Adapter, Part # TC-200A

Your price: $11.50

Linear TC-200A Tilt Compensator TC200A 1 Pack F-Connector High Frequency Attenuator In-Line Filter Female to Male Coupler with Female to Female Barrel Adapter, Part # TC-200A

Linear TC-200A In-Line High Frequency Tilt Compensator

The Model TC-200A Tilt Compensator is an in-line filter designed to create an attenuation loss equal and opposite to cable loss. Coaxial cable attenuates high frequencies greater than low frequencies. This problem is most severe when cascading amplifiers one after another. The signal differences are attenuated to a point where the high frequency signals are so small compared to the low frequency signals that the high frequency signals can no longer be received. The TC-200A Tilt Compensator provides a balanced signal level by compensating for 200 feet of coax cable loss and allowing all signal levels on all channels to be of equal amplitude at distant locations. Therefore, the picture quality on the higher channels will be maintained.

The TC-200A is designed to work with RG-6 coax cable carrying signals in the 5 MHz to 1 GHz range. When an RG-6 cable run reaches 200 feet, install a TC-200A Tilt Compensator whenever an amplifier stage follows. A female barrel connector is included with the TC-200A for in-line applications. The TC-200A is non-directional, the input can be connected to either end.

Specifications:

• Compensates for high frequency signal loss on long coax runs
• Female "F" and male "F" connectors
• Includes Female-Female barrel connector for in-line use

Retail Price: $19.95

Our Discounted Price: $11.50

6 dB Attenuator In-line F-Coaxial Cable Reduce Signal Levels Adapter DC Block F to Male Nickle Plated Coupler 5 - 1750 MHz Connector Female to Male 1 Pack Coaxial Coupler Audio Video Adapter Connector, Part # Steren 201-406

Your price: $0.97

6 dB Attenuator In-line F-Coaxial Cable Reduce Signal Levels Adapter DC Block F to Male Nickle Plated Coupler 5 - 1750 MHz Connector Female to Male 1 Pack Coaxial Coupler Audio Video Adapter Connector, Part # Steren 201-406

The Steren 201-406 Inline 6 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Steren 201-406 Female to Male 6 dB Inline Attenuator Pads
• Frequency Range: 5 - 1750 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $1.95

Our Discounted Price: $0.97

Steren 201-403 3 dB Inline Attenuator Pad 0 - 2000 MHz Female to Male 5% Tolerance Return Loss 20 dB Typical Signal Nickel Plated DC Block 1 Pack Coaxial Coupler Audio Video Adapter, Part # 201-403

Your price: $1.15

Steren 201-403 3 dB Inline Attenuator Pad 0 - 2000 MHz Female to Male 5% Tolerance Return Loss 20 dB Typical Signal Nickel Plated DC Block 1 Pack Coaxial Coupler Audio Video Adapter, Part # 201-403

The Steren 201-403 Inline 3 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Steren 201-403 Female to Male 3 dB Inline Attenuator Pads
• Frequency Range: 0 - 2000 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $1.95

Our Discounted Price: $1.15

Steren 201-416 16 dB Inline Attenuator Pad 0 - 2000 MHz Female to Male 5% Tolerance Return Loss 20 dB Typical Signal Nickel Plated DC Block 1 Pack Coaxial Coupler Audio Video Adapter, Part # 201-416

Your price: $0.85

Steren 201-416 16 dB Inline Attenuator Pad 0 - 2000 MHz Female to Male 5% Tolerance Return Loss 20 dB Typical Signal Nickel Plated DC Block 1 Pack Coaxial Coupler Audio Video Adapter, Part # 201-416

The Steren 201-416 Inline 16 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Steren 201-416 Female to Male 16 dB Inline Attenuator Pads
• Frequency Range: 0 - 2000 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $1.95

Our Discounted Price: $0.85

DC Voltage Blocking Coupler 2 GHz Adapter Female to Male 16 dB Typical Nickle Plate Insertion Loss 0.3 dB Voltage Block 1 Pack Coaxial Audio Video AC/DC Volt Blocking Adapter Connector

Your price: $1.34

DC Voltage Blocking Coupler 2 GHz Adapter Female to Male 16 dB Typical Nickle Plate Insertion Loss 0.3 dB Voltage Block 1 Pack Coaxial Audio Video AC/DC Volt Blocking Adapter Connector

This item is no longer available for purchase.

It has been replaced by the Winegard VB-1000 Voltage Block!!!!

The Steren DC Block has a female and male F type coaxial connection. Simply insert into the line to block DC current from passing through while permitting RF Power to flow. Single 1 Pack.

Specifications:

• Steren 201-500 F Voltage Block
• Insertion Loss: .03 dB
• Return Loss: 16 dB
• Frequency Range: 5 - 1750 MHz
• Used to block voltage from in-line power inserters.
• Sold as Singles

Retail Price: $3.95

Our Discounted Price: $1.34

Linear / Channel Plus 2503 3 dB Inline Attenuator Pad 0 - 2000 MHz Female to Male 5% Tolerance Return Loss 20 dB Typical Signal Nickel Plated DC Block 1 Pack Coaxial Coupler Audio Video Adapter, Part # 2503

Your price: $1.49

Linear / Channel Plus 2503 3 dB Inline Attenuator Pad 0 - 2000 MHz Female to Male 5% Tolerance Return Loss 20 dB Typical Signal Nickel Plated DC Block 1 Pack Coaxial Coupler Audio Video Adapter, Part # 2503

The Inline 3 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Female to Male 3 dB Inline Attenuator Pads
• Frequency Range: 0 - 2000 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $2.49

Our Discounted Price: $1.49

Linear / Channel Plus 2506 6 dB Inline Attenuator DC Block F to Male Nickle Plated Coupler 5 - 1750 MHz Connector Female to Male 1 Pack Coaxial Coupler Audio Video Adapter Connector, Part # 2506

Your price: $0.97

Linear / Channel Plus 2506 6 dB Inline Attenuator DC Block F to Male Nickle Plated Coupler 5 - 1750 MHz Connector Female to Male 1 Pack Coaxial Coupler Audio Video Adapter Connector, Part # 2506

The Inline 6 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Female to Male 6 dB Inline Attenuator Pads
• Frequency Range: 5 - 1750 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $2.95

Our Discounted Price: $0.97

Channel Plus 2501 In-Line Blocking Capacitor F-Connector Type DC Block and IR Control Pulses Passes RF Signal 75 Ohm Female to Male 1 Pack F Type Blocking Capacitor Coaxial Cable Connector Plug Adapter, Part # 2501

Your price: $1.32

Channel Plus 2501 In-Line Blocking Capacitor F-Connector Type DC Block and IR Control Pulses Passes RF Signal 75 Ohm Female to Male 1 Pack F Type Blocking Capacitor Coaxial Cable Connector Plug Adapter, Part # 2501

Channel Plus 2501 Blocking Capacitor

The Model 2501 Blocking Capacitor is used in systems where DC and/or infrared control pulses are present on the coaxial cable. When such signals are not wanted or might be shorted out by downstream video products, a Model 2501 blocking cap can be inserted in an individual coaxial cable feed. The capacitor serves like an open circuit to DC and low frequency IR control signals, yet passes all RF signals on.

Example: Using a 12-volt IR system and not using Model 2100A wall plates at all coax drops, insert a Model 2501 on the end of the coax.

Specifications:

• Blocks DC IR signals
• Passes RF signals
• Type F barrel connector
• 1 piece

Retail Price: $2.95

Our Discounted Price: $1.32

Channel Plus 2501-10 In-Line Blocking Capacitor F-Connector Type DC Block and IR Control Pulses Passes RF Signal 75 Ohm Female to Male 10 Pack F Type Blocking Capacitor Coaxial Cable Connector Plug Adapter, Part # 2501-10

Your price: $12.35

Channel Plus 2501-10 In-Line Blocking Capacitor F-Connector Type DC Block and IR Control Pulses Passes RF Signal 75 Ohm Female to Male 10 Pack F Type Blocking Capacitor Coaxial Cable Connector Plug Adapter, Part # 2501-10

Channel Plus 2501-10 Blocking Capacitor - 10 Pack Lot

The Model 2501-10 Blocking Capacitor (10-pack) is used in systems where DC and/or infrared control pulses are present on the coaxial cable. When such signals are not wanted or might be shorted out by downstream video products, a Model 2501-10 blocking cap can be inserted in an individual coaxial cable feed. The capacitor serves like an open circuit to DC and low frequency IR control signals, yet passes all RF signals on.

Example: Using a 12-volt IR system and not using Model 2100A wall plates at all coax drops, insert a Model 2501 on the end of the coax.

Specifications:

• Blocks DC IR signals
• Passes RF signals
• Type F barrel connector
• 10 piece bulk pack

Retail Price: $21.95

Our Discounted Price: $12.35

Channel Plus LPF-380 Low Pass Filter Channels 2 - 50 380 MHz Removes CATV Channels Above the Pass Band 380 MHz 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-380

Your price: $18.99

Channel Plus LPF-380 Low Pass Filter Channels 2 - 50 380 MHz Removes CATV Channels Above the Pass Band 380 MHz 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-380

Channel Plus LPF-380 Low Pass Filter

The Model LPF-380 Low-pass Filter is used on systems when broadband entertainment feed is supplied by a CATV service. The filter removes all CATV channels above the pass band, allowing insertion of locally-generated Channel Plus modulated channels. In addition, the filter removes cable system noise which degrades the picture quality of the locally-generated channels.

Specifications:

• 0 to 380 MHz bandpass frequency
• Passes off-air TV channels 2 to 13
• Passes CATV channels 2 to 50
• Allows insertion of TV channels 14 to 69
• Allows insertion of CATV channels 55 to 125

Retail Price: $29.95

Our Discounted Price: $18.99

Channel Plus LPF-470 Low Pass Filter Channels 2 - 64 470 MHz Removes CATV Channels Above the Pass Band 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF470

Your price: $19.59

Channel Plus LPF-470 Low Pass Filter Channels 2 - 64 470 MHz Removes CATV Channels Above the Pass Band 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF470

Channel Plus LPF-470 Low Pass Filter

The Model LPF-470 Low-pass Filter is used on systems when broadband entertainment feed is supplied by a CATV service. The filter removes all CATV channels above the pass band, allowing insertion of locally-generated Channel Plus modulated channels. In addition, the filter removes cable system noise which degrades the picture quality of the locally-generated channels.

Specifications:

• 0 to 470 MHz bandpass frequency
• Passes off-air TV channels 2 to 13
• Passes CATV channels 2 to 64
• Allows insertion of TV channels 18 to 69
• Allows insertion of CATV channels 69 to 125

Retail Price: $34.95

Our Discounted Price: $19.59

Channel Plus LPF-600 Low Pass Filter Channels 2 - 86 600 MHz Removes CATV Channels Above the Pass Band 600 MHz 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-600

Your price: $29.85

Channel Plus LPF-600 Low Pass Filter Channels 2 - 86 600 MHz Removes CATV Channels Above the Pass Band 600 MHz 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-600

Channel Plus LPF-600 Low Pass Filter

The Model LPF-600 Low-pass Filter is used on systems when broadband entertainment feed is supplied by a CATV service. The filter removes all CATV channels above the pass band, allowing insertion of locally-generated Channel Plus modulated channels. In addition, the filter removes cable system noise which degrades the picture quality of the locally-generated channels.

Specifications:

• 0 to 600 MHz bandpass frequency
• Passes off-air TV channels 2 to 35
• Passes CATV channels 2 to 86
• Allows insertion of TV channels 40 to 69
• Allows insertion of CATV channels 91 to 125

Retail Price: $47.95

Our Discounted Price: $29.85

Steren 201-408 8 dB Attenuator Pad DC Block F-Type 75 Ohm Female to Male Inline Fixed 5 - 1750 MHz 22 Gauge Spring Steel Nickle Plated In-Line Coupler Connector 1 Pack, Part # 201-408

Your price: $1.20

Steren 201-408 8 dB Attenuator Pad DC Block F-Type 75 Ohm Female to Male Inline Fixed 5 - 1750 MHz 22 Gauge Spring Steel Nickle Plated In-Line Coupler Connector 1 Pack, Part # 201-408

The Steren 201-408 Inline 8 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Steren 201-408 Female to Male 8 dB Inline Attenuator Pads
• Frequency Range: 5 - 1750 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $2.39

Our Discounted Price: $1.20

Steren 201-410 10 dB Attenuator Pad DC Block F-Type 75 Ohm Female to Male Inline Fixed 5 - 1750 MHz 22 Gauge Spring Steel Nickle Plated In-Line Coupler Connector 1 Pack, Part # 201-410

Your price: $1.03

Steren 201-410 10 dB Attenuator Pad DC Block F-Type 75 Ohm Female to Male Inline Fixed 5 - 1750 MHz 22 Gauge Spring Steel Nickle Plated In-Line Coupler Connector 1 Pack, Part # 201-410

The Steren 201-410 Inline 10 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Steren 201-410 Female to Male 10 dB Inline Attenuator Pads
• Frequency Range: 5 - 1750 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $2.39

Our Discounted Price: $1.03

Steren 201-412 12 dB Attenuator Pad DC Block F-Type 75 Ohm Female to Male Inline Fixed 5 - 1750 MHz 22 Gauge Spring Steel Nickle Plated In-Line Coupler Connector 1 Pack, Part # 201-412

Your price: $1.29

Steren 201-412 12 dB Attenuator Pad DC Block F-Type 75 Ohm Female to Male Inline Fixed 5 - 1750 MHz 22 Gauge Spring Steel Nickle Plated In-Line Coupler Connector 1 Pack, Part # 201-412

The Steren 201-412 Inline 12 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Steren 201-412 Female to Male 12 dB Inline Attenuator Pads
• Frequency Range: 5 - 1750 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $2.39

Our Discounted Price: $1.29

Steren 201-420 20 dB Attenuator Pad DC Block F-Type 75 Ohm Female to Male Inline Fixed 5 - 1750 MHz 22 Gauge Spring Steel Nickle Plated In-Line Coupler Connector 1 Pack, Part # 201-420

Your price: $0.86

Steren 201-420 20 dB Attenuator Pad DC Block F-Type 75 Ohm Female to Male Inline Fixed 5 - 1750 MHz 22 Gauge Spring Steel Nickle Plated In-Line Coupler Connector 1 Pack, Part # 201-420

The Steren 201-420 Inline 20 dB Attenuator Pads has a female and male F type coaxial connection. Single 1 Pack.

Specifications:

• Steren 201-420 Female to Male 20 dB Inline Attenuator Pads
• Frequency Range: 5 - 1750 MHz
• Monolithic ceramic Printed Board Circuitry
• Nickle-Plated Machined Brass Construction
• 22 Gauge Spring Steel Center
• Tolerance 5% Return Loss: 20 dB Typical
• Sold as Singles

Retail Price: $2.39

Our Discounted Price: $0.86

Linear LPF-600 Channel Low Pass Filter 2 - 86 600 MHz Removes CATV Channels Above the Pass Band 600 MHz 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-600

Your price: $29.85

Linear LPF-600 Channel Low Pass Filter 2 - 86 600 MHz Removes CATV Channels Above the Pass Band 600 MHz 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-600

Linear LPF-600 Low Pass Filter

The Model LPF-600 Low-pass Filter is used on systems when broadband entertainment feed is supplied by a CATV service. The filter removes all CATV channels above the pass band, allowing insertion of locally-generated Channel Plus modulated channels. In addition, the filter removes cable system noise which degrades the picture quality of the locally-generated channels.

Specifications:

• 0 to 600 MHz bandpass frequency
• Passes off-air TV channels 2 to 35
• Passes CATV channels 2 to 86
• Allows insertion of TV channels 40 to 69
• Allows insertion of CATV channels 91 to 125

Retail Price: $47.95

Our Discounted Price: $29.85

Linear LPF-470 Channel Low Pass Filter 2-64 470 MHz Removes CATV Channels Above the Pass Band 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF470

Your price: $19.59

Linear LPF-470 Channel Low Pass Filter 2-64 470 MHz Removes CATV Channels Above the Pass Band 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF470

Linear LPF-470 Low Pass Filter

The Model LPF-470 Low-pass Filter is used on systems when broadband entertainment feed is supplied by a CATV service. The filter removes all CATV channels above the pass band, allowing insertion of locally-generated Channel Plus modulated channels. In addition, the filter removes cable system noise which degrades the picture quality of the locally-generated channels.

Specifications:

• 0 to 470 MHz bandpass frequency
• Passes off-air TV channels 2 to 13
• Passes CATV channels 2 to 64
• Allows insertion of TV channels 18 to 69
• Allows insertion of CATV channels 69 to 125

Retail Price: $34.95

Our Discounted Price: $19.59

Linear 2501 DC Blocking Capacitor In-Line Blocking Capacitor F-Connector Type DC Block and IR Control Pulses Passes RF Signal 75 Ohm Female to Male 1 Pack Coaxial Cable Connector Plug Adapter, Part # 2501

Your price: $1.32

Linear 2501 DC Blocking Capacitor In-Line Blocking Capacitor F-Connector Type DC Block and IR Control Pulses Passes RF Signal 75 Ohm Female to Male 1 Pack Coaxial Cable Connector Plug Adapter, Part # 2501

Linear 2501 Blocking Capacitor

The Model 2501 Blocking Capacitor is used in systems where DC and/or infrared control pulses are present on the coaxial cable. When such signals are not wanted or might be shorted out by downstream video products, a Model 2501 blocking cap can be inserted in an individual coaxial cable feed. The capacitor serves like an open circuit to DC and low frequency IR control signals, yet passes all RF signals on.

Example: Using a 12-volt IR system and not using Model 2100A wall plates at all coax drops, insert a Model 2501 on the end of the coax.

Specifications:

• Blocks DC IR signals
• Passes RF signals
• Type F barrel connector
• 1 piece

Retail Price: $2.95

Our Discounted Price: $1.32

Linear LPF-380 Low Pass Filter Channels 2 - 50 380 MHz Removes CATV Channels Above the Pass Band 380 MHz 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-380

Your price: $18.95

Linear LPF-380 Low Pass Filter Channels 2 - 50 380 MHz Removes CATV Channels Above the Pass Band 380 MHz 1 Pack In-Line Low Band Pass Filter Coupler Barrel Adapter, Part # LPF-380

Linear LPF-380 Low Pass Filter

The Model LPF-380 Low-pass Filter is used on systems when broadband entertainment feed is supplied by a CATV service. The filter removes all CATV channels above the pass band, allowing insertion of locally-generated Channel Plus modulated channels. In addition, the filter removes cable system noise which degrades the picture quality of the locally-generated channels.

Specifications:

• 0 to 380 MHz bandpass frequency
• Passes off-air TV channels 2 to 13
• Passes CATV channels 2 to 50
• Allows insertion of TV channels 14 to 69
• Allows insertion of CATV channels 55 to 125

Retail Price: $29.95

Our Discounted Price: $18.95

Pico Macom VBC-HRL DC Voltage Blocking Coupler 3 GHz 5 - 3000 MHz Connector Female to Male Nickle Plate Voltage Block 1 Pack Coaxial Coupler Audio Video AC/DC Volt Blocking Adapter Connector, Part # VBCHRL

Your price: $1.32

Pico Macom VBC-HRL DC Voltage Blocking Coupler 3 GHz 5 - 3000 MHz Connector Female to Male Nickle Plate Voltage Block 1 Pack Coaxial Coupler Audio Video AC/DC Volt Blocking Adapter Connector, Part # VBCHRL

The DC Block has a female and male F type coaxial connection. Simply insert into the line to block DC current from passing through while permitting RF Power to flow. Single 1 Pack.

Specifications:

• Pico Macom VBC-HRL F Voltage Block
• AC 60 Volt, DC 48 Volt
• Frequency Range: 5 - 3000 MHz
• Used to block voltage from in-line power inserters.
• Sold as Singles

Retail Price: $3.95

Our Discounted Price: $1.32

Linear 2501-10 In-Line Blocking Capacitor F-Connector Type DC Block and IR Control Pulses Passes RF Signal 75 Ohm Female to Male 10 Pack F Type Blocking Capacitor Coaxial Cable Connector Plug Adapter, Part # 2501-10

Your price: $12.35

Linear 2501-10 In-Line Blocking Capacitor F-Connector Type DC Block and IR Control Pulses Passes RF Signal 75 Ohm Female to Male 10 Pack F Type Blocking Capacitor Coaxial Cable Connector Plug Adapter, Part # 2501-10

Linear 2501-10 Blocking Capacitor - 10 Pack Lot

The Model 2501-10 Blocking Capacitor (10-pack) is used in systems where DC and/or infrared control pulses are present on the coaxial cable. When such signals are not wanted or might be shorted out by downstream video products, a Model 2501-10 blocking cap can be inserted in an individual coaxial cable feed. The capacitor serves like an open circuit to DC and low frequency IR control signals, yet passes all RF signals on.

Example: Using a 12-volt IR system and not using Model 2100A wall plates at all coax drops, insert a Model 2501 on the end of the coax.

Specifications:

• Blocks DC IR signals
• Passes RF signals
• Type F barrel connector
• 10 piece bulk pack

Retail Price: $21.95

Our Discounted Price: $12.35

Pico Macom VBC-HRL-10 DC Voltage Blocking Coupler 3 GHz 5 - 3000 MHz Connector Female to Male Nickle Plate Voltage Block 10 Pack Coaxial Coupler Audio Video AC/DC Volt Blocking Adapter Connector, Part # VBCHRL-10

Your price: $12.00

Pico Macom VBC-HRL-10 DC Voltage Blocking Coupler 3 GHz 5 - 3000 MHz Connector Female to Male Nickle Plate Voltage Block 10 Pack Coaxial Coupler Audio Video AC/DC Volt Blocking Adapter Connector, Part # VBCHRL-10

The DC Block has a female and male F type coaxial connection. Simply insert into the line to block DC current from passing through while permitting RF Power to flow. 10 Pack Lot.

Specifications:

• Pico Macom VBC-HRL F Voltage Block
• AC 60 Volt, DC 48 Volt
• Frequency Range: 5 - 3000 MHz
• Used to block voltage from in-line power inserters.
• 10 Pack Lot

Retail Price: $23.95

Our Discounted Price: $12.00

Channel Master 2810IFD 10 dB AC/DC Passive Attenuator 40-2150 MHz F-Type 75 Ohm Female to Male Inline 24 VDC 1A Max Passing Nickle Plated In-Line Coupler Connector 1 Pack, Part # 2810-IFD

Your price: $1.16

Channel Master 2810IFD 10 dB AC/DC Passive Attenuator 40-2150 MHz F-Type 75 Ohm Female to Male Inline 24 VDC 1A Max Passing Nickle Plated In-Line Coupler Connector 1 Pack, Part # 2810-IFD

Channel Master - A Name You can Trust!!!

Channel Master 2810IFD 40-2150MHz Ultra wideband in-line attenuator. For ease of installation, one end is typ F male and the other end type F female. Prevents excess signal overloading of an amplifier or receiver. Unit is power passive so it is possible to pass DC line power. Single 1 Pack.

Specifications:

• Channel Master 2810IFD Inline 10 dB Female-Male Attenuator
• Frequency Range: 40 - 2150 MHz
• 24 VDC 1A Max Passing
• Sold as Singles

Retail Price: $2.95

Our Discounted Price: $1.16

Pico Macom VBC DC Voltage Blocking Coupler 5 - 1000 MHz 1 GHz Coaxial DC Voltage Block Female to Male 1 Pack Coax Cable Systems F Connector Audio Video AC/DC Volt Blocking Connector, Part # VBC

Your price: $1.18

Pico Macom VBC DC Voltage Blocking Coupler 5 - 1000 MHz 1 GHz Coaxial DC Voltage Block Female to Male 1 Pack Coax Cable Systems F Connector Audio Video AC/DC Volt Blocking Connector, Part # VBC

The Pico Macom VBC DC Block has a female and male F type coaxial connection. Used to stop voltage from entering a device. Protects sensitive test equipment from damage test. Two bandwidths available for use in CATV and Satellite applications. Low insertion loss for transparent operation. High return loss for unsurpassed performance in digital signal environments. Single 1 Pack.

Specifications:

• Pico Macom VBC Voltage Block
• Band Width: 5 - 1000 MHz
• Flatness: 1 GHz > 0.5 dB
• Insertion Loss: 40 MHz < 0.3 dB
• Return Loss: > 25 dB (min)
• Sold as Singles

Retail Price: $2.95

Our Discounted Price: $1.18

Channel Master 2806IFD 6 dB 2 GHz Attenuator 24 VDC Passive 1A Max DC - 2050 MHz AC/DC Passive F-Type 75 Ohm Female to Male Inline Passing Nickle Plated In-Line Coupler Connector 1 Pack, Part # 2806-IFD

Your price: $1.09

Channel Master 2806IFD 6 dB 2 GHz Attenuator 24 VDC Passive 1A Max DC - 2050 MHz AC/DC Passive F-Type 75 Ohm Female to Male Inline Passing Nickle Plated In-Line Coupler Connector 1 Pack, Part # 2806-IFD

Channel Master - A Name You can Trust!!!

Channel Master 2806IFD DC-2050 MHz in-line attenuator. For ease of installation, one end is type F male and the other end type F female. Prevents excess signal overloading of an amplifier or receiver. Unit is power passive so it is possible to pass DC line power. Single 1 Pack.

Specifications:

• Channel Master 2806IFD Inline 6 dB Female-Male Attenuator
• Frequency Range: DC - 2150 MHz
• 24 VDC 1A Max Passing
• Sold as Singles

Retail Price: $2.95

Our Discounted Price: $1.09